Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _079315 PARK ASSIST / MONITORING _0385738 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer mirror retractor RH

·

Harness or connector

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E410127E02
2.583,1.479 2.74,1.677 0.156,0.198 10 false 2 2.552,1.906 2.708,2.104 0.156,0.198 10 false 1 2.302,1.552 2.458,1.75 0.156,0.198 10 false + 2.333,1.948 2.49,2.146 0.156,0.198 10 false - 0.656,2.385 1.313,2.615 0.656,0.229 10 false IND2 0.646,2.573 2.365,2.969 1.719,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.438,3.708 2.771,4.104 2.333,0.396 10 false Outer Rear View Mirror Assembly RH 3.813,1.49 4.281,1.688 0.469,0.198 10 false BSR+ 6.031,1.583 6.5,1.781 0.469,0.198 10 false OMIR 5.729,1.479 6.198,1.677 0.469,0.198 10 false 4 5.948,3.625 6.417,3.823 0.469,0.198 10 false e3 5.896,3.792 7.125,4.417 1.229,0.625 10 false Blind Spot Monitor Sensor RH 4.313,1.458 4.542,1.646 0.229,0.188 10 false 1 4.302,1.854 4.573,2.021 0.271,0.167 10 false 11 4.052,1.875 4.292,2.042 0.24,0.167 10 false E 0.458,3.563 0.927,3.76 0.469,0.198 10 false R10 2.615,2.469 4.333,2.865 1.719,0.396 10 false Outer Mirror Retractor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.
E406932C17
1.5,0.25 1.906,0.542 0.406,0.292 1.875,1.146 2.385,0.51 2.385,0.51 2.583,0.51 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.906,0.521 0.344,0.198 10 false e3 2.667,0.427 3.073,0.615 0.406,0.188 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the R10 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e3-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR RETRACTOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR RETRACTOR RH
a.

Disconnect the R10 outer rear view mirror assembly RH connector.


b.
E410122C02
1.594,1.969 1.427,1.969 1.427,1.969 1.167,1.25 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.677,1.896 2.167,2.083 0.49,0.188 10 false BSR+
*a Front view of outer mirror retractor LH
(to Vehicle Harness)


Disconnect the IND2 outer mirror RH (outer rear view mirror indicator RH).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPLACE OUTER MIRROR RETRACTOR RH

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
a.

Remove the outer mirror RH (outer rear view mirror indicator RH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer mirror RH (outer rear view mirror indicator RH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)