Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION SYSTEM (for 1GD-FTV)
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0383350 MANUAL TRANSMISSION SYSTEM(for 1GD-FTV) J

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM(for 1GD-FTV)  Pattern Select Switch iMT Mode Circuit  


DESCRIPTION

Operating the iMT switch illuminates the iMT indicator light in the combination meter. This displays the iMT system standby condition.

WIRING DIAGRAM

C325752E28
5.219,0.75 5.833,0.948 0.615,0.198 10 false MTMS 5,0.75 5.281,0.948 0.281,0.198 10 false 8 3.75,0.75 4.365,0.948 0.615,0.198 10 false 5 3.5,0.75 3.667,1 0.167,0.25 10 false S 2.719,0.75 3.333,0.948 0.615,0.198 10 false E 2.479,0.75 2.677,0.948 0.198,0.198 10 false 2 2.833,1.302 3.448,1.5 0.615,0.198 10 false N14 2.833,1.5 4.594,1.854 1.76,0.354 10 false iMT Switch (Pattern Select Switch Assembly) 0.469,3.219 2.167,3.417 1.698,0.198 10 false : CAN Communication Line 2.333,3 4.198,3.25 1.865,0.25 10 false Combination Meter Assembly 5.667,3 6.281,3.198 0.615,0.198 10 false N2 5.667,3.167 6.281,3.365 0.615,0.198 10 false ECM 5.917,0.438 6.531,0.635 0.615,0.198 10 false 12 V

PROCEDURE

1.READ VALUE USING GTS (IMT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
iMT SW iMT switch status ON or OFF
·

ON: iMT switch being pressed and held

·

OFF: iMT switch not pressed


-
Powertrain > Engine > Data List
Tester Display
iMT SW
50003 372 570

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

2.CHECK HARNESS AND CONNECTOR (IMT SWITCH - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IMT SWITCH - BODY GROUND)
a.
C414308C02
0.323,0.906 0.688,1.156 0.365,0.25 1.198,1.729 1.448,1.313 true 1.073,1.76 1.229,1.958 0.156,0.198 10 false E 0.375,0.958 0.823,1.146 0.448,0.188 10 false N14 0.208,0.177 0.51,0.385 0.302,0.208 10 false *a
*a Front view of wire harness connector
(to iMT Switch)


Disconnect the iMT switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IMT SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IMT SWITCH - ECM)
a.

Disconnect the iMT switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-5 (S) - N2-8 (MTMS) Always Below 1 Ω
N14-5 (S) or N2-8 (MTMS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT IMT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT IMT SWITCH

OK

NG