These DTCs are stored when a malfunction occurs in the navigation antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | Short in GPS Antenna | Current to the navigation antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Short circuit) |
·
Telephone transceiver assembly ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Harness or connector |
| B15C1 | Open in GPS Antenna | Current for navigation antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Open circuit) |
·
Telephone transceiver assembly ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - N141-1 (GPS) | Always | Below 1 Ω |
| B-3a - N141-1a | Always | Below 1 Ω |
| B-3 or N141-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the antenna cord sub-assembly connector.
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N141-1 (GPS) - N140-1 (ANT2) | Always | Below 1 Ω |
| N141-1a - N140-1a | Always | Below 1 Ω |
| N141-1 (GPS) or N140-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT