The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors is detected consecutively 3 times.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2325 | LIN Communication Bus Malfunction | The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Multiplex network master switch assembly ·
Power window regulator motor assembly LH ·
Power window regulator motor assembly RH ·
Harness or connector |
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the GTS and vehicle begins.
When the power window regulator motor assembly LH*1 or RH*2 is removed and reinstalled or replaced, the power window regulator motor assembly LH*1 or RH*2 must be initialized.
*1: for LHD
*2: for RHD
Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is not output | A |
| DTC B2325 is output (for LHD) | B |
| DTC B2325 is output (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the R12 power window regulator motor assembly LH connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2321 is output | B |
A
B
Disconnect the R11 multiplex network master switch assembly connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B1206 and B2321 are output | B |
A
B
Disconnect the R7 power window regulator motor assembly RH connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2322 is output | B |
A
B
Disconnect the R11 multiplex network master switch assembly connector.
Disconnect the R12 power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R11-11 (LIN2) - R12-9 (LIN) | Always | Below 1 Ω |
| R11-11 (LIN2) or R12-9 (LIN) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R2 power window regulator motor assembly RH connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2321 is output | B |
A
B
Disconnect the R1 multiplex network master switch assembly connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B1206 and B2321 are output | B |
A
B
Disconnect the R17 power window regulator motor assembly LH connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2322 is output | B |
A
B
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Disconnect the R12*1 or R17*2 power window regulator motor assembly LH connector.
*1: for LHD
*2: for RHD
Disconnect the R7*1 or R2*2 power window regulator motor assembly RH connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| A-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 3B instrument panel junction block assembly connector.
Disconnect the R12*1 or R17*2 power window regulator motor assembly LH connector.
*1: for LHD
*2: for RHD
Disconnect the R7*1 or R2*2 power window regulator motor assembly RH connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - Body ground | Always | 10 kΩ or higher |
| 3B-17 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the R1 multiplex network master switch assembly connector.
Disconnect the R2 power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R1-11 (LIN2) - R2-9 (LIN) | Always | Below 1 Ω |
| R1-11 (LIN2) or R2-9 (LIN) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG