These DTCs indicate that the variable vane DC motor of the turbocharger is malfunctioning. The ECM monitors the variable vane DC motor current to detect an open or short in the variable vane DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The variable vane DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the variable vane DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (Variable vane DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (Variable vane DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P004512 | Turbocharger/Supercharger Boost Control "A" Circuit Short to Battery | Overcurrent is detected 25 times or more (1 trip detection logic). | ·
Short in variable vane DC motor (turbocharger nozzle vane control actuator) circuit ·
Turbocharger nozzle vane control actuator ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored | SAE Code: P0048 |
| P004514 | Turbocharger/Supercharger Boost Control "A" Circuit Short to Ground or Open | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). | ·
Open in variable vane DC motor (turbocharger nozzle vane control actuator) circuit ·
Turbocharger nozzle vane control actuator ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored | SAE Code: P0047 |
| P004600 | Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance | The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more (1 trip detection logic). | ·
Turbocharger nozzle vane control actuator ·
Turbocharger sub-assembly ·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | DTC stored | SAE Code: P0046 |
If DTC P004512, P004514 and/or P004600 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
Vehicle surge when driving with full load
If DTC P004512, P004514 and/or P004600 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P004512
P004514 |
2 seconds after engine is started, race engine for 1 second |
| P004600 | Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P004600 is output | A |
| DTC P004512 and/or P004514 is output | B |
| DTC P004512, P004514 and/or P004600 and other DTCs are output | C |
If codes other than DTC P004512, P004514 and/or P004600 are output, perform troubleshooting for those DTCs first.
A
B
C
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Remove the turbocharger sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL
Inspect the turbocharger nozzle vane plate.
Remove the e-washer from the turbocharger nozzle vane control actuator.
Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.
| Result | Proceed to |
|---|---|
| Catches, but operates* | OK |
| Gets stuck and does not operate | NG |
*: Check several times.
OK
NG
Replace the turbocharger nozzle vane control actuator.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected
(Variable Vane DC Motor) |
Disconnect the variable vane DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1 to 100 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the variable vane DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E41-1 (M-) - E7-2 (VNM-) | Always | Below 1 Ω |
| E41-2 (M+) - E7-1 (VNM+) | Always | Below 1 Ω |
| E41-1 (M-) or E7-2 (VNM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| E41-2 (M+) or E7-1 (VNM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo Open Bank 1.
| Tester Display |
|---|
| Activate the VN Turbo Open Bank 1 |
Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger nozzle vane control actuator.
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT