Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P052FA3  Glow Plug Control Module 1 System Voltage System Voltage High  P068386  Glow Plug Control Module 1 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid  


DESCRIPTION

The glow system consists of the glow plug controller, glow plug assemblies and ECM. The glow plug controller turns on the glow plug assembly of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plug assemblies can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052FA3 Glow Plug Control Module 1 System Voltage System Voltage High The glow plug controller recognizes the battery voltage as being 39.99 V or higher 3 times or more when the glow plug assemblies are on (2 trip detection logic). Glow plug controller Comes on DTC stored SAE Code: P052F
P068386 Glow Plug Control Module 1 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid When the glow plug assemblies are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic).
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM


Comes on DTC stored SAE Code: P0683

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052FA3
P068386
Enter check mode

WIRING DIAGRAM

A444426E01
1.604,0.969 2.063,1.167 0.458,0.198 10 false A32 1.604,0.573 2.063,0.771 0.458,0.198 10 false A32 1.615,1.396 2.073,1.594 0.458,0.198 10 false A31 1.615,1.802 2.073,2 0.458,0.198 10 false A31 1.615,2.229 2.073,2.427 0.458,0.198 10 false A30 1.604,3.521 2.063,3.719 0.458,0.198 10 false A32 1.604,2.646 2.063,2.844 0.458,0.198 10 false A30 1.615,3.99 2.073,4.188 0.458,0.198 10 false A29 1.615,4.448 2.073,4.646 0.458,0.198 10 false A32 1.375,0.552 1.688,0.75 0.313,0.198 10 false SI 1.385,0.958 1.698,1.156 0.313,0.198 10 false DI 1.271,1.385 1.583,1.583 0.313,0.198 10 false GL1 1.271,1.802 1.583,2 0.313,0.198 10 false GL2 1.26,2.208 1.573,2.406 0.313,0.198 10 false GL3 1.26,2.635 1.573,2.833 0.313,0.198 10 false GL4 1.333,3.521 1.646,3.719 0.313,0.198 10 false +B 1.198,4 1.802,4.208 0.604,0.208 10 false BATT 1.229,4.438 1.833,4.646 0.604,0.208 10 false GND 1.208,5.615 1.813,5.823 0.604,0.208 10 false GLOW 1.688,0.375 2,0.573 0.313,0.198 10 false 3 1.698,0.792 2.01,0.99 0.313,0.198 10 false 5 1.677,1.208 1.99,1.406 0.313,0.198 10 false 1 1.688,1.615 2,1.813 0.313,0.198 10 false 2 1.688,2.042 2,2.24 0.313,0.198 10 false 1 1.698,2.458 2.01,2.656 0.313,0.198 10 false 2 3.292,1.781 3.802,1.99 0.51,0.208 10 false GLW2 3.302,2.229 3.813,2.438 0.51,0.208 10 false GLW3 3.302,2.646 3.813,2.854 0.51,0.208 10 false GLW4 3.302,1.396 3.813,1.604 0.51,0.208 10 false GLW1 3.104,1.281 3.417,1.479 0.313,0.198 10 false 1 3.104,1.708 3.417,1.906 0.313,0.198 10 false 2 3.115,2.104 3.427,2.302 0.313,0.198 10 false 3 3.125,2.531 3.438,2.729 0.313,0.198 10 false 4 3.25,2.917 3.708,3.115 0.458,0.198 10 false E80 3.25,3.094 5.083,3.49 1.833,0.396 10 false Glow Plug Assembly 2.802,4.646 3.698,4.833 0.896,0.188 10 false GLOW 1.698,3.792 2.01,3.99 0.313,0.198 10 false 1 1.708,3.323 2.021,3.521 0.313,0.198 10 false 4 1.698,4.24 2.01,4.438 0.313,0.198 10 false 1 5.115,4.969 5.427,5.167 0.313,0.198 10 false 1 1.521,5.281 1.833,5.479 0.313,0.198 10 false 2 1.177,5.281 1.49,5.479 0.313,0.198 10 false 1 2.552,3.875 2.865,4.073 0.313,0.198 10 false 3 3.323,4.24 3.635,4.438 0.313,0.198 10 false 2 3.344,3.885 3.656,4.083 0.313,0.198 10 false 5 5.844,0.573 6.302,0.771 0.458,0.198 10 false E6 5.844,0.979 6.302,1.177 0.458,0.198 10 false E6 5.833,4.333 6.292,4.531 0.458,0.198 10 false N2 5.177,4.719 6.073,4.906 0.896,0.188 10 false EFI NO. 3 6.167,4.344 7.063,4.531 0.896,0.188 10 false GREL 5.844,4.146 6.302,4.344 0.458,0.198 10 false 19 5.854,6.125 6.313,6.323 0.458,0.198 10 false 14 5.844,6.333 6.302,6.531 0.458,0.198 10 false N2 5.844,0.792 6.302,0.99 0.458,0.198 10 false 10 5.844,0.375 6.302,0.573 0.458,0.198 10 false 11 6.156,0.563 6.667,0.771 0.51,0.208 10 false GLDO 6.167,0.979 6.677,1.188 0.51,0.208 10 false GLDI 6.146,6.333 7.042,6.521 0.896,0.188 10 false MREL 4.292,6.229 4.604,6.427 0.313,0.198 10 false 2 3.5,6.24 3.813,6.438 0.313,0.198 10 false 1 3.521,5.833 3.833,6.031 0.313,0.198 10 false 3 4.323,5.833 4.635,6.031 0.313,0.198 10 false 5 5.115,4.49 5.427,4.688 0.313,0.198 10 false 2 1.167,6.083 2.208,6.542 1.042,0.458 10 false EFI-MAIN 1.5,5.844 1.813,6.042 0.313,0.198 10 false 2 1.188,5.854 1.5,6.052 0.313,0.198 10 false 1 0.521,6.344 1.125,6.552 0.604,0.208 10 false FL MAIN 2.563,4.229 2.875,4.427 0.313,0.198 10 false 1 3.677,6.698 4.927,7.219 1.25,0.521 10 false EFI MAIN 0.573,4.823 3.635,5.021 3.063,0.198 10 false Glow Plug Controller 6.344,6.969 7.156,7.25 0.813,0.281 10 false ECM 0.667,6.99 3.729,7.188 3.063,0.198 10 false Battery 4.146,5.292 5.042,5.479 0.896,0.188 10 false EFI NO. 4 4.625,4.99 4.938,5.188 0.313,0.198 10 false 1 4.188,4.979 4.5,5.177 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P068386 is output A
DTC P052FA3 is output B




A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

12.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.
A241954C42
0.542,1 1.01,1.271 0.469,0.271 1.917,1.677 1.76,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.646,1.052 1,1.271 0.354,0.219 10 false A32 1.885,1.667 2.198,1.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A32-4 (+B) - Body ground Ignition switch ON 11 to 14 V
A32-4 (+B) - Body ground Ignition switch off Below 0.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI MAIN RELAY)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.


b.
A241954C43
0.542,1 1.01,1.271 0.469,0.271 1.302,1.646 1.49,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.625,1.052 0.979,1.271 0.354,0.219 10 false A32 1.146,1.667 1.635,1.875 0.49,0.208 10 false GND
*a Front view of wire harness connector
(to Glow Plug Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-3 (SI) - E6-11 (GLDO) Always Below 1 Ω
A32-5 (DI) - E6-10 (GLDI) Always Below 1 Ω
A32-3 (SI) or E6-11 (GLDO) - Body ground and other terminals Always 10 kΩ or higher
A32-5 (DI) or E6-10 (GLDI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.

OK:

No DTC is output.


HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI MAIN RELAY)
a.

Disconnect the glow plug controller connector.


b.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-4 (+B) - EFI MAIN relay terminal 5 Always Below 1 Ω
A32-4 (+B) or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CHARGING SYSTEM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>1GD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END