The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto-Resistive Element).
The G2 signal plate has 3 teeth on its outer circumference and is installed on the exhaust camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P03402A | Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range | No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (1 trip detection logic). | ·
Camshaft position sensor ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0340 |
| P034031 | Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal | Camshaft position sensor signal is not input with an engine speed of 650 rpm or more (1 trip detection logic). | ·
Camshaft position sensor ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0340 |
If DTC P03402A or P034031 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2-
Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P03402A | Crank engine for 4 seconds (STA on) |
| P034031 | Idling for 5 second or more (STA off) |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Cranking is OK. | A |
| Does not crank at all. | B |
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>PROBLEM SYMPTOMS TABLE
Inspect the ECM using an oscilloscope.
While the engine is idling, check the waveform between the terminals of the ECM connector.
| *a | Component with harness connected
(ECM) |
- | - |
| Tester Connection | Tester Range | Condition | Specified Condition |
|---|---|---|---|
| E8-27 (G2+) - E8-18 (G2-) | 2 V/DIV.
20 msec./DIV. |
Idling | Correct waveform as shown in illustration |
| E8-28 (NE+) - E8-19 (NE-) | 2 V/DIV.
20 msec./DIV. |
Idling | Correct waveform as shown in illustration |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ECM using an oscilloscope.
While the engine is idling, check the waveform between the terminals of the ECM connector.
Inspect the camshaft position sensor and crankshaft position sensor timing.
The G2 signal is output 3 times for every 2 crankshaft rotations (720°CA).
| Tester Connection | Tester Range | Condition | Specified Condition |
|---|---|---|---|
| E8-27 (G2+) - E8-18 (G2-) | 2 V/DIV.
20 msec./DIV. |
Idling | Correct waveform as shown in illustration |
| E8-28 (NE+) - E8-19 (NE-) | 2 V/DIV.
20 msec./DIV. |
Idling | Correct waveform as shown in illustration |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P03402A or P034031 is output | A |
| DTC is not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
When the G2 signal appears to be malfunctioning, check the exhaust camshaft.
If the teeth of the timing rotor are damaged, perform replacement.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>CAMSHAFT (w/o EGR Cooler)>REMOVAL
When the Ne signal appears to be malfunctioning, check the following parts.
Installation condition of the crankshaft position sensor
Crank angle sensor plate
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Clearance |
Check the camshaft position sensor installation.
Camshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the timing rotor of the exhaust camshaft.
Camshaft timing rotor does not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft position sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust camshaft.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>CAMSHAFT (w/o EGR Cooler)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Securely reinstall the camshaft position sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT