Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388652 ECD SYSTEM(w/o EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E74
0.25,1.302 1.5,1.583 1.25,0.281 10 false from Speed Sensor 1.802,1.948 3.021,2.156 1.219,0.208 10 false Skid Control ECU 3.469,1.958 5.469,2.313 2,0.354 10 false Combination Meter Assembly 2.896,0.604 4.052,0.844 1.156,0.24 10 false 4-Pulse Signal 6.094,1.906 6.521,2.115 0.427,0.208 10 false ECM 4.802,0.604 5.958,0.844 1.156,0.24 10 false 4-Pulse Signal

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050031 Vehicle Speed Sensor "A" No Signal for automatic transmission: Condition (a) is met for 5 seconds or more (1 trip detection logic):

(a) While vehicle being driven, no vehicle speed sensor signal transmitted to ECM.


for manual transmission: Conditions (a) and (b) are met for 6.2 seconds or more (2 trip detection logic):

(a) The fuel-cut operation is being performed.

(b) No speed signal is input to the ECM.


·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


Comes on DTC stored SAE Code: P0500

Related Data List
DTC No. Data List
P050031 Vehicle Speed

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P050031 Drive the vehicle at 10 km/h (6.25 mph) or more and perform a fuel cut

WIRING DIAGRAM

A335120E25
0.271,1.469 1.521,1.969 1.25,0.5 10 false from Brake Actuator Assembly 2.063,1.375 2.375,1.573 0.313,0.198 10 false 20 2.302,1.375 2.615,1.573 0.313,0.198 10 false SI 3.521,1.375 3.833,1.573 0.313,0.198 10 false +S 3.802,1.365 4.146,1.802 0.344,0.438 10 false 36 2.135,2.26 2.677,2.625 0.542,0.365 10 false N22 2.135,2.427 4.167,2.896 2.031,0.469 10 false Combination Meter Assembly 4.875,1.375 5.188,1.573 0.313,0.198 10 false 10 5.115,1.375 5.531,1.594 0.417,0.219 10 false SPD 5.5,2.292 5.813,2.49 0.313,0.198 10 false N2 5.823,2.292 6.313,2.521 0.49,0.229 10 false ECM 5.042,2.646 6.302,3.01 1.26,0.365 10 false to Other ECUs

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 372 212

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N22-36 (+S) - N2-10 (SPD) Always Below 1 Ω
N22-36 (+S) or N2-10 (SPD) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at 10 km/h (6.25 mph) or more and perform a fuel cut.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Confirm that the pending DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END