Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P03351F  Crankshaft Position Sensor "A" Circuit Intermittent  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and Magneto-Resistive Element (MRE) type sensor. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03351F Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):

(a) Engine speed is 1000 rpm or more.

(b) Starter signal is off.

(c) 3 seconds or more have elapsed since the starter signal switched from on to off.


·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Does not come on DTC stored SAE Code: P0339
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range No crankshaft position sensor signal to the ECM while cranking (1 trip detection logic).
·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored SAE Code: P0335
P033531 Crankshaft Position Sensor "A" No Signal The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic).
·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored SAE Code: P0335

Related Data List
DTC No. Data List
P03351F
P03352A
P033531
Engine Speed

HINT:

If DTC P03351F, P03352A and/or P033531 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P03351F Engine running at 1000 rpm or higher with vehicle stationary
P03352A
P033531
Crank or start engine

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>INITIALIZATION).


HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Primary / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Does not crank at all.* B


HINT:

*: When the engine cannot crank, there may be a malfunction in the starter assembly.




A

2.READ VALUE USING GTS (ENGINE SPEED)

B

GO TO PROBLEM SYMPTOMS TABLE (ENGINE DOES NOT CRANK (DOES NOT START))

2.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P03351F, P03352A AND/OR P033531)

NG

4.INSPECT ECM (CRANKSHAFT POSITION SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P03351F, P03352A AND/OR P033531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and run it at 1000 rpm or higher for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P03351F, P03352A and/or P033531 is output B



A

B

4.INSPECT ECM (CRANKSHAFT POSITION SENSOR)
4.INSPECT ECM (CRANKSHAFT POSITION SENSOR)
a.

Inspect the ECM using an oscilloscope.

i.

While the engine is idling, check the waveform between the terminals of the ECM connector.

A340469C11
5.521,0.219 5.938,0.479 0.417,0.26 6.167,1.344 5.896,0.958 true 5.615,1.365 5.854,0.896 true 3.26,0.063 3.885,0.281 0.625,0.219 10 false 2 V/DIV. 1.448,1.49 2.406,1.688 0.958,0.198 10 false 50 msec./DIV. 3.5,1.135 3.938,1.302 0.438,0.167 10 false GND 0.115,1.01 0.396,1.198 0.281,0.188 10 false NE 5.219,1.354 5.833,1.552 0.615,0.198 10 false 19 (NE-) 6.188,1.354 6.833,1.563 0.646,0.208 10 false 28 (NE+) 5.604,0.281 6.042,0.448 0.438,0.167 10 false E8 4.26,0.094 4.875,0.292 0.615,0.198 10 false *a
*a Component with harness connected
(ECM)
- -


OK:
Tester Connection Tester Range Condition Specified Condition
E8-28 (NE+) - E8-19 (NE-) 2 V/DIV.
50 msec./DIV.
Cranking to idling Correct waveform as shown in illustration




Result:
Proceed to
OK
NG



NG

5.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

OK

11.REPLACE ECM
5.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
A316078C05
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

6.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)

NG

10.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
6.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cranks or deformation.



Result:
Proceed to
OK
NG



OK

7.REPLACE CRANKSHAFT POSITION SENSOR

NG

9.REPLACE CRANKSHAFT
7.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and run it at 1000 rpm or higher for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE CRANKSHAFT

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
a.

Securely reinstall the crankshaft position sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED