The vacuum switching valve assembly (for EGR Bypass Valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P245A12 | Exhaust Gas Recirculation Cooler Bypass Control Circuit High Bank 1 Circuit Short to Battery | Open or short in the vacuum switching valve assembly (for EGR Bypass Valve) for 3 seconds (1 trip detection logic). | ·
Open or short in vacuum switching valve assembly (for EGR Bypass Valve) circuit ·
Vacuum switching valve assembly (for EGR Bypass Valve) ·
ECM |
Comes on | DTC stored | SAE Code: P245D |
| P245A14 | Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Bank 1 Circuit Short to Ground or Open | Open or short in the vacuum switching valve assembly (for EGR Bypass Valve) for 3 seconds (1 trip detection logic). | ·
Open or short in vacuum switching valve assembly (for EGR Bypass Valve) circuit ·
Vacuum switching valve assembly (for EGR Bypass Valve) ·
ECM |
Comes on | DTC stored | SAE Code: P245C |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P245A12
P245A14 |
Ignition switch ON for 3 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the vacuum switching valve assembly (for EGR Bypass Valve).
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve assembly (for EGR Bypass Valve) connector.
| *a | Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for EGR Bypass Valve)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E109-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve assembly (for EGR Bypass Valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E109-2 (ECBV) - E5-16 (ECBV) | Always | Below 1 Ω |
| E109-2 (ECBV) or E5-16 (ECBV) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
If the voltage at the vacuum switching valve assembly (for EGR Bypass Valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve assembly (for EGR Bypass Valve) and No. 1 engine room relay block and junction block assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum control valve set.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT