Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P050500  Idle Control System  


DESCRIPTION

The ECU provides control so that the actual idling speed matches the target idling speed based on feedback on the fuel injection volume from the injector.

If deposits accumulate in the injection holes in the injector assembly, the injection volume will decrease and the speed will drop. If an injection hole develops a malfunction (becomes corroded), the injection volume will increase and the speed will rise.

Even if a deviation occurs between the target idling speed and actual idling speed and the idling control feedback value is stuck at the upper limit or lower limit, P050500 will be stored as an idling control malfunction after the deviation between the idling speed and actual idling speed continuously exceeds the threshold for 60 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050500 Idle Control System The speed is at least 90 rpm lower or 200 rpm higher than the target speed with the idling control feedback value stuck at the upper limit or lower limit for 60 seconds or more (2 trip detection logic).
·

Injector assembly

·

Engine malfunction

·

Auxiliary component malfunction


Class B2 DTC stored SAE Code: P0505

Related Data List
DTC No. Data List
P0505
·

Target Idle Engine Speed

·

Engine Speed

·

Injection Feedback Volume for Idle



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P050500 Warm up the engine and idle it for 120 seconds or more

CAUTION / NOTICE / HINT

NOTICE:


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050500)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456
Result:
Result Proceed to
DTC P050500 is output A
DTC P050500 and other DTCs are output B


HINT:

If any DTCs other than P050500 are output, troubleshoot those DTCs first.




A

2.CHECK ENGINE AND AUXILIARY COMPONENTS

B

2.CHECK ENGINE AND AUXILIARY COMPONENTS
a.

Check the engine and auxiliary components for malfunctions.

HINT:
·

Check for any abnormal noises.

·

Check for slow cranking even if the battery is fully charged.

·

Check for drive belt slippage during high loads.




Result:
Proceed to
OK
NG



NG

3.REPAIR OR REPLACE MALFUNCTIONING PARTS

OK

5.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS
3.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace malfunctioning parts.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P050500)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P050500)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Warm up the engine and idle it for 120 seconds or more.


i.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

k.

Confirm that the DTC is not output again.

Result:
Result Proceed to
DTC P050500 is output A
No DTC is output B




B

END

A

5.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS
5.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P050500)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P050500)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Warm up the engine and idle it for 120 seconds or more.


i.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

k.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END