The No. 2 rear cooling unit damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air outlet damper to the appropriate position, which controls the rear air outlet switching. The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the No. 2 air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1449 | Air Outlet Damper Control Servo Motor Circuit (Rear) | ·
Diagnosis condition: During No. 2 rear cooling unit damper servo sub-assembly (mode) operation ·
Malfunction status: The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning ·
Detection time: Continuously for 30 seconds or more |
·
No. 2 rear cooling unit damper servo sub-assembly ·
No. 2 air conditioning harness assembly ·
Air conditioning amplifier assembly ·
Rear cooling unit assembly |
Memorized |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | During No. 2 rear cooling unit damper servo sub-assembly operation | ○ | ○ |
| Malfunction Status | The damper servo operation request signal is output but the position information of the servo does not change | ○ | - |
| The damper servo operation request signal is output but the position information of the servo is malfunctioning | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions match either of these patterns, a DTC will be output.
Confirm that no mechanical problems are present because this DTC can be stored when either a damper link or damper is mechanically locked.
When installing a damper servo motor, make sure to install it correctly.
After replacing a damper servo motor, make sure to perform Servo Motor Initialization.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1449 and B1497 are output | B |
A
B
Check that the No. 2 rear cooling unit damper servo sub-assembly is installed correctly.
The No. 2 rear cooling unit damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 rear cooling unit damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the No. 1 rear cooling unit damper servo sub-assembly with the No. 2 rear cooling unit damper servo sub-assembly and connect the connectors to them.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Clear the DTC.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1447 is output | A |
| DTC B1449 is output | B |
| DTCs B1447 and B1449 are not output | C |
Codes other than DTC B1447 and B1449 may be output at this time, but they are not related to this check.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING