Before removing the rear air conditioning unit, set the air conditioning to FOOT mode.
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DRAIN ENGINE COOLANT
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (COOLING)>COOLANT>REPLACEMENT
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT
3.REMOVE WHEEL ASSEMBLY (Rear RH)
65631D
4.REMOVE REAR FRONT WHEEL HOUSE PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR WHEEL HOUSE PLATE>REMOVAL
76907
5.REMOVE QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>SIDE MUDGUARD (for Wagon)>REMOVAL
65637B
6.REMOVE REAR WHEEL HOUSE LINER RH
|
Screw |
|
Screw Clip |
|
Clip |
Remove the 2 screws.
Rotate and remove the 11 screw clips.
Remove the 6 clips.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Bend the liner inward and detach it from the stud bolts to remove the rear wheel house liner RH.
87245E
7.DISCONNECT HEATER WATER HOSE INLET E
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet E.
Do not apply excessive force to the water hose and heater water hose inlet E.
Prepare a drain pan or cloth in case the coolant leaks.
87246G
8.DISCONNECT HEATER WATER HOSE OUTLET G
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet G.
Do not apply excessive force to the water hose and heater water hose outlet G.
Prepare a drain pan or cloth in case the coolant leaks.
88727D
9.DISCONNECT COOLER REFRIGERANT SUCTION PIPE D
Remove the bolt and disconnect the cooler refrigerant suction pipe D.
Remove the O-ring from the cooler refrigerant suction pipe D.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88716D
10.DISCONNECT COOLER REFRIGERANT LIQUID PIPE D
Remove the bolt and disconnect the cooler refrigerant liquid pipe D.
Remove the O-ring from the cooler refrigerant liquid pipe D.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
11.REMOVE REAR SEAT ASSEMBLY RH
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
67935
12.REMOVE BACK DOOR SCUFF PLATE
73233D
13.REMOVE OUTER LAP BELT ANCHOR COVER (w/ Seat Belt)
73360D
14.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (w/ Seat Belt)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
67917C
15.REMOVE REAR DOOR SCUFF PLATE RH
67871E
16.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
Pull back the No. 1 slide door weatherstrip RH so that the rear quarter trim board assembly RH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL
62510M
17.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
62471D
18.REMOVE REAR UPPER PILLAR GARNISH RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
58793C
19.REMOVE NO. 1 JACK CARRIER BRACKET
Remove the tool bag.
Remove the 3 bolts and No. 1 jack carrier bracket.
88892Q
20.REMOVE COOLER PLATE
Detach the claw and remove the cooler plate.
88566B
21.REMOVE NO. 2 COOLER AIR DUCT
w/ Bypass Hose:
Remove the hose.
|
Move in this Direction |
Move the No. 2 cooler air duct as shown in the illustration.
|
Remove in this Direction |
Remove the No. 2 cooler air duct as shown in the illustration.
87030
22.REMOVE AIR CONDITIONING BLOWER ASSEMBLY
Remove the 2 bolts A.
| *1 | Air Conditioning Tube and Accessory | - | - |
| *a | Guide | *b | Harness Clamp |
|
Bolt A |
|
Connector |
|
Bolt B |
|
Remove in this Direction |
Detach the claw and disconnect the air conditioning tube and accessory assembly from the body.
Disconnect the drain cooler hose.
Disconnect each connector.
Disconnect the harness clamp to disconnect the wire harness.
Remove the 3 bolts B.
Detach the guide and remove the air conditioning blower assembly.
62180E
23.REMOVE REAR CURTAIN SHIELD AIRBAG ASSEMBLY LH (w/ Curtain Shield Airbag)
88566C
24.REMOVE NO. 3 COOLER AIR DUCT
Remove the 3 clips and No. 3 cooler air duct.