Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 7GR-FKS(w/ Variable Flow Control Solenoid Valve)) › 2019.06–2021.07
RM35X0E _55 Steering _078944 POWER ASSIST SYSTEMS _0388796 VANE PUMP(for 7GR-FKS(w/ Variable Flow Control Solenoid Valve)) A

POWER ASSIST SYSTEMS  VANE PUMP(for 7GR-FKS(w/ Variable Flow Control Solenoid Valve))  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during vane pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system


-

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



NOTICE:
·

When using a vise, do not overtighten it.

·

When installing the parts indicated by arrows, coat them with power steering fluid.

Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (for 7GR-FKS(w/ Variable Flow Control Solenoid Valve))>COMPONENTS



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE FRONT WHEEL RH

Hide 11209 4.REMOVE V-BANK COVER SUB-ASSEMBLY (w/ Cover)

Hide 17751 6.REMOVE NO. 1 AIR CLEANER INLET

Hide 7.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 16361A 8.REMOVE FAN AND GENERATOR V BELT

Hide 9.DISCONNECT WIRE HARNESS BRACKET

a.
C412809

Disconnect the 2 connectors.


b.

Remove the bolt and disconnect the wire harness bracket.


Hide 44348D 10.DISCONNECT NO. 2 OIL RESERVOIR TO PUMP HOSE

a.
C412811

Slide the clip and disconnect the No. 2 oil reservoir to pump hose from the vane pump assembly.


b.

Drain the power steering fluid.


Hide 44410 11.DISCONNECT PRESSURE FEED TUBE ASSEMBLY

a.
C412813

Remove the union bolt and disconnect the pressure feed tube assembly.


b.

Remove the gasket.


Hide 44310 12.REMOVE VANE PUMP ASSEMBLY

a.
C412817

Remove the 2 bolts and vane pump assembly.