Home › Audio / Visual / Telematics › AUDIO / VIDEO › STEREO JACK ADAPTER ASSEMBLY (for LHD) › from 2019.06
RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0380040 STEREO JACK ADAPTER ASSEMBLY(for LHD) A

AUDIO / VIDEO  STEREO JACK ADAPTER ASSEMBLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 stereo jack adapter assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION (w/o Console Tray)

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/o Console Tray)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55631A 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER

Hide 55011A 7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 53601 10.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 77306 11.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 55432D 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55044C 13.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55433B 14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55445B 15.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Knee Airbag)

Hide 55313 16.REMOVE LOWER INSTRUMENT PANEL LH (w/o Knee Airbag)

Hide 73900 17.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 67911B 18.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67913B 19.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62111C 20.REMOVE COWL SIDE TRIM BOARD RH

Hide 55632B 21.REMOVE NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT

Hide 55012A 22.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55317A 23.REMOVE INSTRUMENT SIDE PANEL RH

Hide 55642 24.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER

Hide 55438A 25.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER

Hide 26.REMOVE FRONT CONSOLE BOX (w/ Console Tray)

Hide 58533C 27.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58534E 28.REMOVE CENTER FLOOR CARPET COVER LH

Hide 55646 29.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER

Hide 86190C 30.REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY

a.
E416309C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the No. 1 stereo jack adapter assembly as shown in the illustration.