Home › Vehicle Interior › LIGHTING (INT) › GLOVE BOX LIGHT › from 2019.06
RM35X0E _58 Vehicle Interior _078381 LIGHTING (INT) _0396491 GLOVE BOX LIGHT A

LIGHTING (INT)  GLOVE BOX LIGHT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during glove box light assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55631A 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER

Hide 55011A 7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 53601 10.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 77306 11.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 55432D 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55044C 13.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55433B 14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 73900 15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 67911B 16.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67913B 17.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62111C 18.REMOVE COWL SIDE TRIM BOARD RH

Hide 55632B 19.REMOVE NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT

Hide 55012A 20.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55317A 21.REMOVE INSTRUMENT SIDE PANEL RH

Hide 55642 22.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER

Hide 55312 23.REMOVE LOWER INSTRUMENT PANEL

Hide 55438A 24.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER

Hide 25.REMOVE FRONT CONSOLE BOX (w/ Console Tray)

Hide 58533C 26.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58534E 27.REMOVE CENTER FLOOR CARPET COVER LH

Hide 55646 28.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER

Hide 55434B 29.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55320 30.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 81260 31.REMOVE GLOVE BOX LIGHT ASSEMBLY

a.
E420245C01
0,0 0,0 false
V113147

Remove in this Direction


Turn in the direction indicated by the arrow as shown in the illustration.


b.
E420246C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction indicated by the arrow as shown in the illustration and remove the glove box light assembly.