The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front curtain shield airbag assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE ROOF HEADLINING ASSEMBLY
for Wagon:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
for Semi-trim:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
62180D
4.REMOVE FRONT CURTAIN SHIELD AIRBAG ASSEMBLY LH
|
Deployment Side |
When storing the front curtain shield airbag assembly LH, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Remove the front curtain shield airbag assembly LH deployment portion in the following order.
Using needle-nose pliers, remove the 2 pins from the roof side inner garnish clip.
| *A | for Standard Roof | *B | for High Roof |
| *1 | Roof Side Inner Garnish Clip | *2 | Clip |
|
Remove in this Direction | - | - |
for Standard Roof:
Using 2 thin bladed screwdrivers, detach the claw and remove the 2 roof side inner garnish clips together with the front curtain shield airbag assembly LH deployment portion.
for High Roof:
Using 2 thin bladed screwdrivers, detach the claw and remove the clip and roof side inner garnish clip together with the front curtain shield airbag assembly LH deployment portion.
Detach the claw.
Remove the front curtain shield airbag assembly LH inflator in the following order.
The bolt must not be reused.
| *A | for Standard Roof | *B | for High Roof |
| *a | Strap | *b | Rear Side Bolt |
| *c | Front Curtain Shield Airbag Assembly LH Inflator | - | - |
Remove the bolt and detach the hook to remove the front curtain shield airbag assembly LH strap.
Remove the bolt and rear side of the front curtain shield airbag assembly LH deployment portion.
Remove the 2 bolts.
Detach the hook to remove the front curtain shield airbag assembly LH inflator.
When reusing the front curtain shield airbag assembly LH:
Do not reuse the roof side inner garnish clip.
| *A | for Standard Roof | *B | for High Roof |
| *1 | Roof Side Inner Garnish Clip | *2 | Clip |
for Standard Roof:
Detach the claw and remove the 2 roof side inner garnish clips.
for High Roof:
Detach the claw and remove the clip and roof side inner garnish clip.