The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 3 side airbag sensor removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67604
3.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (for Van)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (except Wagon)>DISASSEMBLY
65988A
4.REMOVE SUNSHADE HOOK (for Wagon, w/ Sunshade)
67693B
5.REMOVE UPPER SLIDE DOOR TRIM COVER LH (for Wagon)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (for Wagon)>DISASSEMBLY
67668A
6.REMOVE SLIDE DOOR WINDOW GARNISH LH (for Wagon)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (for Wagon)>DISASSEMBLY
67488A
7.REMOVE REAR DOOR REAR GUIDE BRACKET GARNISH LH (for Wagon)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (for Wagon)>DISASSEMBLY
81380D
8.REMOVE STEP LIGHT ASSEMBLY (for Wagon)
67690C
9.REMOVE SLIDE DOOR TRIM BOARD ASSEMBLY LH (for Wagon)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (for Wagon)>DISASSEMBLY
89831G
10.REMOVE NO. 3 SIDE AIRBAG SENSOR
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
for Van:
Remove the bolt.
Loosen the bolt while holding the No. 3 side airbag sensor because the No. 3 side airbag sensor claw is easily damaged.
If the No. 3 side airbag sensor has been dropped, replace it with a new one.
Detach the claw to remove the No. 3 side airbag sensor.
If the No. 3 side airbag sensor has been dropped, replace it with a new one.
for Wagon:
Remove the bolt.
Loosen the bolt while holding the No. 3 side airbag sensor because the No. 3 side airbag sensor guide is easily damaged.
If the No. 3 side airbag sensor has been dropped, replace it with a new one.
Detach the guide to remove the No. 3 side airbag sensor.
If the No. 3 side airbag sensor has been dropped, replace it with a new one.
11.REMOVE CLIP
If the clip is removed, do not reuse it.
Perform this procedure only when replacement of the clip is necessary.
Detach claw and remove the clip.