The side collision sensor LH circuit consists of the airbag sensor assembly, No. 4 side airbag sensor LH, No. 2 side airbag sensor LH and No. 3 side airbag sensor LH.
The No. 4 side airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.
These DTCs are stored when a malfunction is detected in the No. 4 side airbag sensor LH or airbag sensor assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1685 | Rear Floor No.2 Airbag Sensor LH | Either condition is met:
·
A No. 4 side airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 4 side airbag sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
| B1687 | Lost Communication with Rear Floor No.2 Airbag Sensor LH | Either condition is met:
·
A No. 4 side airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 4 side airbag sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
| *1 | No. 4 Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor LH |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the No. 4 side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>DTC CHECK / CLEAR
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1685 or B1687 is output |
| DTC B1680 or B1682 is output |
| DTCs B1680, 1682, B1685 and B1687 are not output |
Codes other than DTCs B1680, 1682, B1685 and B1687 may be output at this time, but they are not related to this check.
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the No. 4 side airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B1685 or B1687 is output
DTC B1680 or B1682 is output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Rear Pillar)>REMOVAL
DTCs B1680, 1682, B1685 and B1687 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING