The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 2 side airbag sensor or No. 4 side airbag sensor removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
73370E
3.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for Van)
Remove the rear seat outer belt assembly LH retractor.
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Van)>REMOVAL
62632D
4.REMOVE REAR QUARTER TRIM BOARD LH (for Van)
5.REMOVE REAR NO. 3 SEAT ASSEMBLY (for Wagon)
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
6.REMOVE REAR SEAT ASSEMBLY (for Wagon)
for Folding Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
73233
7.REMOVE OUTER LAP BELT ANCHOR COVER (for Wagon, w/ Seat Belt)
73570A
8.REMOVE NO. 3 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (for Wagon, w/ Seat Belt)
67881A
9.REMOVE BACK DOOR WEATHERSTRIP (for Wagon)
67935
10.REMOVE BACK DOOR SCUFF PLATE (for Wagon)
67872A
11.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH (for Wagon)
Remove the rear side of the No. 1 slide door weatherstrip LH so that the rear quarter trim board assembly LH can be removed.
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62520B
12.REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Wagon)
When removing and installing the No. 2 side airbag sensor or No. 4 side airbag sensor installed on the driver side, perform this procedure.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
62510M
13.REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Wagon)
When removing and installing the No. 2 side airbag sensor or No. 4 side airbag sensor installed on the passenger side, perform this procedure.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
89831C
14.REMOVE NO. 2 SIDE AIRBAG SENSOR
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
for Van:
Remove the bolt.
Loosen the bolt while holding the No. 2 side airbag sensor because the No. 2 side airbag sensor claw is easily damaged.
If the No. 2 side airbag sensor has been dropped, replace it with a new one.
Detach the claw and remove the No. 2 side airbag sensor.
for Wagon:
Remove the bolt.
Loosen the bolt while holding the No. 2 side airbag sensor because the No. 2 side airbag sensor guide is easily damaged.
If the No. 2 side airbag sensor has been dropped, replace it with a new one.
Detach the guide and remove the No. 2 side airbag sensor.
89831J
15.REMOVE NO. 4 SIDE AIRBAG SENSOR (for Wagon)
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Remove the bolt.
Loosen the bolt while holding the No. 4 side airbag sensor because the No. 4 side airbag sensor guide is easily damaged.
If the No. 4 side airbag sensor has been dropped, replace it with a new one.
Detach the guide to remove the No. 4 side airbag sensor.