Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SWITCH › from 2019.06
RM35X0E _56 Audio / Visual / Telematics _079315 PARK ASSIST / MONITORING _0397123 PANORAMIC VIEW MONITOR SWITCH A

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the panoramic view monitor switch removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 55631A 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER

Hide 55011A 4.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55044C 5.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55404E 6.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 33622 7.DISCONNECT NO. 1 SHIFT LEVER KNOB COVER

Hide 33504F 8.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 35970F 9.REMOVE POSITION INDICATOR HOUSING ASSEMBLY

Hide 55900 10.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 67912A 11.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 12.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 13.REMOVE COWL SIDE TRIM BOARD LH

Hide 55318C 14.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 15.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 53601 16.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 77306 17.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 55432D 18.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55433B 19.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 73900 20.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 67911B 21.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67913B 22.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62111C 23.REMOVE COWL SIDE TRIM BOARD RH

Hide 55632B 24.REMOVE NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT

Hide 55012A 25.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55317A 26.REMOVE INSTRUMENT SIDE PANEL RH

Hide 55642 27.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER

Hide 55312 28.REMOVE LOWER INSTRUMENT PANEL

Hide 55438A 29.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER

Hide 30.REMOVE FRONT CONSOLE BOX (w/ Console Trey)

Hide 58533C 31.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58534E 32.REMOVE CENTER FLOOR CARPET COVER LH

Hide 55646 33.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER

Hide 55434B 34.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55320 35.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 55413D 36.REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL

Hide 55410C 37.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55670 38.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 55447C 39.REMOVE NO. 2 SWITCH HOLE BASE

Hide 84721B 40.REMOVE PANORAMIC VIEW MONITOR SWITCH

a.
B552453C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver, detach the claw to remove the panoramic view monitor switch as shown in the illustration.

HINT:

Tape the screwdriver tip before use.