Home › Drivetrain › CLUTCH › CLUTCH PEDAL › from 2019.06
RM35X0E _52 Drivetrain _078837 CLUTCH _0382376 CLUTCH PEDAL A

CLUTCH  CLUTCH PEDAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch pedal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55631A 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER (for LHD)

Hide 55011A 7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 55432D 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for LHD)

Hide 55433B 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 73900 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55445B 13.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Driver Side Knee Airbag)

Hide 55313 14.REMOVE LOWER INSTRUMENT PANEL LH (w/o Driver Side Knee Airbag)

Hide 31453A 15.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

C410803

a.

Remove the clutch master cylinder push rod clevis with hole pin and clip.


Hide 88280A 16.REMOVE CLUTCH SWITCH ASSEMBLY

Hide 55107A 17.REMOVE CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.

w/ Intelligent Manual Transmission:

i.
C410805

Disconnect the 2 connectors and clamp.



b.

w/o Intelligent Manual Transmission:

i.
C410806

Disconnect the connector.



c.
C410807

for LHD:

i.

Remove the bolt, 2 nuts and clutch pedal support sub-assembly.



d.

for RHD:

i.

Remove the bolt, 2 nuts and clutch pedal support sub-assembly.

CAUTION:

While taking care not to pinch your hand, depress the clutch pedal.


NOTICE:

When removing the clutch pedal, do not damage the No. 1 air duct.




Hide 89280 18.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY (w/ Intelligent Manual Transmission)

Hide 84520 19.REMOVE CLUTCH START SWITCH ASSEMBLY

a.
C410809

Remove the nut and clutch start switch assembly.


Hide 31394A 20.REMOVE PEDAL SPRING WITH HOOK

C410810

a.

Remove the pedal spring with hook.


b.
C410820C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the pedal spring with hook.


Hide 31301 21.REMOVE CLUTCH PEDAL SUB-ASSEMBLY

a.
C410812

Remove the bolt, nut and clutch pedal sub-assembly from the clutch pedal support sub-assembly.


Hide 31353 22.REMOVE CLUTCH PEDAL SPRING HOLDER

C410813

a.

Remove the clutch pedal spring holder.


Hide 31301B 23.REMOVE NO. 1 CLUTCH PEDAL CUSHION

a.
C410817

Remove the No. 1 clutch pedal cushion from the clutch pedal sub-assembly.


Hide 31324A 24.REMOVE CLUTCH PEDAL SHAFT COLLAR

C410818

a.

Remove the 2 clutch pedal bushes and clutch pedal shaft collar.


Hide 31301P 25.REMOVE CLUTCH PEDAL TURNOVER BUSH

a.
C410815

Remove the clutch pedal turnover bush from the clutch pedal sub-assembly.


Hide 31453B 26.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.
C410823N01
2.094,1.51 2.479,1.865 2.479,1.865 2.563,1.729 false 2.427,1.917 2.885,2.115 0.458,0.198 10 false SST

Using SST and a hammer, tap out the clutch master cylinder push rod clevis bush from the clutch pedal sub-assembly.

SST
09201-01055  
09950-70010  (09951-07100)


Hide 31395 27.REMOVE PEDAL SPRING HOOK

a.
C410826

Remove the pedal spring hook from the clutch pedal support sub-assembly.


Hide 31321 28.REMOVE CLUTCH PEDAL PAD

a.
C410824

Remove the clutch pedal pad from the clutch pedal sub-assembly.


Hide 29.REMOVE PEDAL SUPPORT TO COWL PLATE

a.
C410808

Remove the bolt and pedal support to cowl plate from the clutch pedal support sub-assembly.


b.
C413178

Remove the nut clip.


Hide 31301S 30.REMOVE NO. 2 CLUTCH PEDAL CUSHION

a.
C413181

Remove the No. 2 clutch pedal cushion from the clutch pedal sub-assembly.


b.
C410828

Remove the No. 2 clutch pedal cushion from the clutch pedal sub-assembly.