Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR › from 2019.06
RM35X0E _59 Vehicle Exterior _079318 WINDOW / GLASS _0384709 POWER WINDOW REGULATOR MOTOR A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Front door window regulator assembly LH

·

Front door window regulator assembly RH

·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function


(Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 69278B 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 67602 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68172A 7.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

Hide 68195B 8.REMOVE FRONT DOOR REAR BELT SEAL LH

Hide 68193C 9.REMOVE FRONT DOOR FRONT BELT SEAL LH

Hide 86160 10.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67626A 11.REMOVE NO. 2 DOOR TRIM BRACKET

Hide 67832 12.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 67838F 13.REMOVE FRONT DOOR NO. 4 SERVICE HOLE COVER LH (w/ Curtain Shield Airbag)

Hide 68151D 14.DISCONNECT FRONT DOOR GLASS RUN LH

Hide 67402F 15.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

Hide 68102 16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 68151D 17.REMOVE FRONT DOOR GLASS RUN LH

Hide 67834 18.REMOVE FRONT DOOR NO. 2 SERVICE HOLE COVER LH

Hide 69820 19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

Hide 85720C 20.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B537074

Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws and power window regulator motor assembly LH from the front door window regulator sub-assembly LH.