Home › Vehicle Interior › SEAT BELT › FRONT CENTER SEAT OUTER BELT (for Sliding Bench Seat Type) › from 2019.06
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0389010 FRONT CENTER SEAT OUTER BELT(for Sliding Bench Seat Type) A

SEAT BELT  FRONT CENTER SEAT OUTER BELT(for Sliding Bench Seat Type)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat 3 point type belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Front Seat Side Airbag)

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 72329D 4.REMOVE SEAT ADJUSTER BOLT COVER RH

Hide 72525M 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

Hide 71811T 6.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 73120 7.REMOVE FRONT SEAT 3 POINT TYPE BELT ASSEMBLY LH (SEAT ANCHOR)

a.
B560470C01
1.521,1.375 2.24,1.146 true 0.25,1.75 0.646,1.375 true 2.24,1.01 2.51,1.229 0.271,0.219 12 true *A 0.063,1.75 0.333,1.969 0.271,0.219 12 true *A
*A for Wagon


Detach the hook.


b.

for Van, w/ Seat Belt Warning System:

i.
B548473C04
0.781,0.594 1.365,0.688 1.365,0.688 1.104,0.323 true 1.375,0.573 1.635,0.802 0.26,0.229 12 true *A
*A w/ Center Seat Occupant Detection Sensor


Detach the claw and clamp.


ii.

Disconnect the connector.



c.

w/ Center Seat Occupant Detection Sensor:

i.

Disconnect the connector.



d.

for Wagon:

i.
B544965

Disconnect the connector.


ii.

Detach the claw and clamp.



e.
B548476

Remove the bolt.


f.
B541176C01
0,0 0,0 false
V100135

Band


Detach the band and remove the seat anchor of the front seat 3 point type belt assembly LH and front seat inner belt assembly RH.


Hide 73373 9.REMOVE REAR SEAT SHOULDER BELT COVER

Hide 71705F 10.REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY RH (for Wagon)

Hide 71073A 11.REMOVE FRONT SEATBACK COVER SUB-ASSEMBLY RH

Hide 74810L 14.REMOVE FRONT PROTECTOR ASSEMBLY RH

Hide 71H75B 15.REMOVE RH SEATBACK FRAME RECLINING ADJUSTER INSIDE COVER

Hide 73120 16.REMOVE FRONT SEAT 3 POINT TYPE BELT ASSEMBLY LH

a.

Remove the 3 nuts A and reclining sensor of the front seat 3 point type belt assembly LH.

B548478C01
4.625,0.479 5.021,0.813 0.396,0.333 12 false *A 4.646,2.021 4.99,2.292 0.344,0.271 12 false *B 2.542,0.677 2.719,0.875 0.177,0.198 10 true B 2.271,1.917 2.448,2.115 0.177,0.198 10 true B 0.927,2.188 1.104,2.385 0.177,0.198 10 true A 1.5,1.948 1.677,2.146 0.177,0.198 10 true A 1.74,2.99 1.917,3.188 0.177,0.198 10 true A
*A for LHD *B for RHD



b.

Remove the 2 nuts B and retractor of the front seat 3 point type belt assembly LH.


c.

Detach the guide and remove the front seat 3 point type belt assembly LH.