Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Bench Seat Type) › from 2019.06
RM35X0E _58 Vehicle Interior _079257 SUPPLEMENTAL RESTRAINT SYSTEMS _0384941 FRONT SEAT SIDE AIRBAG ASSEMBLY(for Bench Seat Type) A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY(for Bench Seat Type)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

·

Be sure to read Precaution thoroughly before servicing.


·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 72329D 4.REMOVE SEAT ADJUSTER BOLT COVER RH

Hide 72525M 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

Hide 71811T 6.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 73373 9.REMOVE REAR SEAT SHOULDER BELT COVER

Hide 71705F 10.REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY RH (for Wagon)

Hide 71073A 11.REMOVE FRONT SEATBACK COVER SUB-ASSEMBLY RH

Hide 73910B 14.REMOVE FRONT SEAT AIRBAG ASSEMBLY RH

CAUTION:
B399378C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the front seat airbag assembly RH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B535124

Disconnect the airbag wire harness from the seat cushion side:

NOTICE:

When disconnecting the airbag wire harness, take care not to damage the airbag wire harness.


i.

Detach the claw and disconnect the airbag connector.


ii.

Detach the wire harness clamp.



b.
B535125

Disconnect the airbag wire harness from the seatback side:

NOTICE:

When disconnecting the airbag wire harness, take care not to damage the airbag wire harness.


i.

Detach the wire harness clamp.



c.
B535126

Remove the nut and front seat airbag assembly RH together with the No. 2 airbag bracket.

CAUTION:
·

Do not reuse the nut.

·

If the installation surface or surrounding area of the front seat airbag assembly RH is deformed or damaged, replace the front seatback frame sub-assembly RH with a new one.




Hide 89178C 15.REMOVE NO. 2 AIRBAG BRACKET

a.
B524624

Remove the 2 nuts and No. 2 airbag bracket from the front seat airbag assembly RH.

CAUTION:
·

Do not reuse the nut.

·

If the No. 2 airbag bracket is deformed or damaged, replace it with a new one.