Home › Vehicle Interior › SEAT › OCCUPANT DETECTION SENSOR (for Manual Captain Seat) › from 2019.06
RM35X0E _58 Vehicle Interior _078601 SEAT _0399975 OCCUPANT DETECTION SENSOR(for Manual Captain Seat) A

SEAT  OCCUPANT DETECTION SENSOR(for Manual Captain Seat)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the occupant detection sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

The procedure listed below is a representative example.

·

Use the same procedure for first row and second row, unless otherwise specified.



PROCEDURE

Hide 1. PRECAUTION (for First Row)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.



NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

If the pretensioner has been deployed, replace any damaged parts as necessary.



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)

a.

Disconnet the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Hide 71849L 4.REMOVE NO. 1 SEAT ADJUSTER COVER CAP LH

Hide 72216B 5.REMOVE NO. 1 SEAT TRACK HANDLE CONTROL LEVER LH

Hide 72526J 6.REMOVE NO. 1 SEAT RECLINING ADJUSTER RELEASE HANDLE LH

Hide 71324Q 7.REMOVE NO. 1 SEAT CUSHION LH (for First Row)

Hide 71834J 8.REMOVE NO. 1 SEAT OUTER NO. 1 RECLINING COVER LH

Hide 71849K 9.REMOVE SEAT SIDE TABLE ADJUSTER COVER CAP (for First Row, RH Side)

Hide 78060C 10.REMOVE NO. 1 SEAT SIDE TABLE ASSEMBLY (for First Row, RH Side)

Hide 71826A 11.REMOVE NO. 1 SEAT INNER CUSHION MOULDING RH

Hide 72848D 12.REMOVE NO. 1 SEAT NO. 1 ARMREST CAP LH

Hide 72890C 13.REMOVE LH SEAT NO. 1 SEAT ARMREST ASSEMBLY LH

Hide 72880C 14.REMOVE LH SEAT NO. 1 SEAT ARMREST ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73375 15.REMOVE REAR SEAT SHOULDER BELT COVER LH

Hide 73390 16.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (ANCHOR)

Hide 17.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD

Hide 79076N 18.REMOVE NO. 1 SEAT OUTER LEG COVER SUB-ASSEMBLY LH (for First Row)

Hide 79076M 19.REMOVE NO. 1 SEAT INNER LEG COVER SUB-ASSEMBLY RH (for First Row)

Hide 79959F 20.REMOVE NO. 1 SEAT LEG COVER LH (for First Row)

Hide 79959J 21.REMOVE NO. 2 SEAT NO. 1 LEG COVER LH (for Second Row)

Hide 79077G 22.REMOVE NO. 2 SEAT OUTER LEG COVER SUB-ASSEMBLY LH (for Second Row)

Hide 79077G 23.REMOVE NO. 2 SEAT INNER LEG COVER SUB-ASSEMBLY RH (for Second Row, w/o Power Supply Unit)

Hide 79959K 24.REMOVE NO. 2 SEAT NO. 2 LEG COVER LH (for Second Row)

Hide 25.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.

Detach the hook.

B552975C01
3.125,1.573 3.469,2.156 3.469,2.156 3.75,1.573 true 1.719,1.813 1.958,2.031 0.24,0.219 12 true *A 3.365,2.177 3.625,2.396 0.26,0.219 12 true *B 4.74,1.823 4.979,2.042 0.24,0.219 12 true *A
*A for First Row *B for Second Row



b.

for First Row:

i.

Remove the 4 clips.



c.

for Second Row:

i.

Remove the 2 clips.



d.
B552976C01
0,0 0,0 false
V100155

Protective Tape


Disconnect the connector of the occupant detection sensor.


e.

Using a thin-bladed screwdriver, detach the claw and remove the connector of the occupant detection sensor.

HINT:

Tape the thin-bladed screwdriver tip before use.



f.

Remove the separate type rear seat cushion cover with pad.


Hide 79136C 26.REMOVE NO. 1 SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

a.
B552978

Remove the 6 hog rings.


b.
B552980

Remove the 15 hog rings and No. 1 seat cushion pad LH (occupant detection sensor).