Home › Vehicle Interior › SEAT › OCCUPANT DETECTION SENSOR (for Power Captain Seat) › from 2019.06
RM35X0E _58 Vehicle Interior _078601 SEAT _0399976 OCCUPANT DETECTION SENSOR(for Power Captain Seat) A

SEAT  OCCUPANT DETECTION SENSOR(for Power Captain Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

The procedure listed below is a representative example.

·

Use the same procedure for first row and second row, unless otherwise specified.



PROCEDURE

Hide 79136C 1.INSTALL NO. 1 SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

HINT:

When installing a No. 1 seat cushion cover sub-assembly LH, refer to Precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>PRECAUTION


a.
B548157C01
1.865,3.74 1.927,3.104 1.927,3.104 2.125,3.104 false 2.146,2.99 2.458,3.146 0.313,0.156 10 false *a 1.365,0.646 1.563,0.854 0.198,0.208 10 true (1) 1.927,0.646 2.125,0.854 0.198,0.208 10 true (2) 1.656,1.198 1.854,1.406 0.198,0.208 10 true (3) 1.208,1.198 1.406,1.406 0.198,0.208 10 true (4) 2.083,1.198 2.281,1.406 0.198,0.208 10 true (5) 1.646,1.646 1.844,1.854 0.198,0.208 10 true (6) 1.177,1.646 1.375,1.854 0.198,0.208 10 true (7) 2.115,1.646 2.313,1.854 0.198,0.208 10 true (8) 2.385,0.583 2.583,0.792 0.198,0.208 10 true (9) 2.469,0.823 2.75,1.031 0.281,0.208 10 true (10) 2.531,1.25 2.813,1.458 0.281,0.208 10 true (11) 2.365,0.333 2.646,0.542 0.281,0.208 10 true (12) 2.354,0.063 2.635,0.271 0.281,0.208 10 true (13) 0.802,0.583 1.073,0.792 0.271,0.208 10 true (14) 0.708,0.823 0.979,1.031 0.271,0.208 10 true (15) 0.656,1.24 0.927,1.448 0.271,0.208 10 true (16) 0.823,0.323 1.094,0.531 0.271,0.208 10 true (17) 0.823,0.052 1.094,0.26 0.271,0.208 10 true (18)
*a Hog Ring Pliers
V100155

Fastening tape


Attach the fastening tape.


b.

Using hog ring pliers, install the No. 1 seat cushion pad LH (occupant detection sensor) to the No. 1 seat cushion cover sub-assembly LH with 18 new hog rings in the order shown in the illustration.

NOTICE:
·

Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.




c.
B548159C01
1.75,3.99 1.823,3.396 1.823,3.396 2,3.396 false 2.01,3.281 2.198,3.469 0.188,0.188 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install 6 new hog rings.

NOTICE:

Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.



Hide 2.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Hide 79968W 3.INSTALL LH SEAT REAR NO. 1 SEAT LEG SIDE COVER

Hide 71H76N 4.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER

Hide 79959F 5.INSTALL NO. 1 SEAT LEG COVER LH

Hide 6.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

Hide 73390 7.INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (ANCHOR)

Hide 72046G 8.INSTALL LH SEAT NO. 1 SEAT NO. 2 TRACK COVER SUB-ASSEMBLY

Hide 72345Z 9.INSTALL LH SEAT NO. 1 SEAT NO. 2 STAND FRAME CAP

Hide 73375 10.INSTALL REAR SEAT SHOULDER BELT COVER LH

Hide 71H75R 11.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH

Hide 72803H 12.INSTALL LH SEAT REAR NO. 1 SEAT ARMREST FRAME SUB-ASSEMBLY RH

Hide 66990E 13.INSTALL REAR NO. 1 SEAT CUP HOLDER ASSEMBLY LH

Hide 71826C 14.INSTALL REAR SEAT CUSHION MOULDING LH

Hide 71866D 15.INSTALL LH SEAT REAR NO. 1 SEAT COVER BEZEL

Hide 71H74 16.INSTALL REAR SEAT LOWER CUSHION SHIELD LH (for Second Row)

Hide 71848W 17.INSTALL LH SEAT NO. 1 SEAT ADJUSTER COVER CAP

Hide 72840K 18.INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY LH

Hide 84923 19.INSTALL REAR POWER SEAT SWITCH

Hide 78060C 20.INSTALL NO. 1 SEAT SIDE TABLE ASSEMBLY (for First Row, RH Side)

Hide 72804E 21.INSTALL LH SEAT REAR NO. 1 SEAT ARMREST FRAME SUB-ASSEMBLY LH

Hide 71844J 22.INSTALL REAR NO. 1 SEAT NO. 2 RECLINING COVER LH

Hide 72C45 23.INSTALL LH SEAT NO. 1 SEAT NO. 3 STAND FRAME CAP (for First Row)

Hide 71849L 24.INSTALL NO. 1 SEAT ADJUSTER COVER CAP LH

Hide 71324R 25.INSTALL REAR NO. 1 SEAT CUSHION LH (for First Row)

Hide 72890C 26.INSTALL LH SEAT NO. 1 SEAT ARMREST ASSEMBLY

Hide 72345Y 27.INSTALL LH SEAT NO. 1 SEAT NO. 1 STAND FRAME CAP

Hide 72526J 28.INSTALL NO. 1 SEAT RECLINING ADJUSTER RELEASE HANDLE LH

Hide 30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for First Row)

Hide 31. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for First Row)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 34.INSPECT SEAT BELT WARNING SYSTEM

Hide 36.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)