Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS (except Wagon) › from 2019.06
RM35X0E _59 Vehicle Exterior _079318 WINDOW / GLASS _0384711 BACK DOOR GLASS(except Wagon) A

WINDOW / GLASS  BACK DOOR GLASS(except Wagon)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Emergency hammer caution label (Type B) is only inner side.


PROCEDURE

Hide 87950 1.REMOVE OUTER UNDER REAR VIEW MIRROR ASSEMBLY (w/ Outer Under Rear View Mirror)

Hide 81570 2.REMOVE CENTER STOP LIGHT ASSEMBLY

Hide 69298 3.REMOVE BACK DOOR INSIDE HANDLE COVER (w/ Handle, w/ Cover)

Hide 69291 4.REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY (w/ Handle)

Hide 69783B 5.REMOVE BACK DOOR INSIDE HANDLE BEZEL (w/ Handle, w/o Illumination)

Hide 69783B 6.REMOVE BACK DOOR INSIDE HANDLE BEZEL (w/ Handle, w/ Illumination)

Hide 67961A 7.REMOVE BACK DOOR PULL STRAP

Hide 67751 8.REMOVE BACK DOOR TRIM BOARD

Hide 9.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 85110R 10.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 85143R 11.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 82186 12.REMOVE NO. 1 REAR WINDOW WIRE (w/ Rear Window Defogger)

a.
B544249C01
0,0 0,0 false
V100135

Wire Harness Connector
V100136

Bolt


Disconnect the wire harness connector.


b.

Remove the bolt.


c.

Detach the clamp and remove the No. 1 rear window wire.


Hide 68131 13.REMOVE BACK DOOR GLASS

a.

w/ Rear Window Defogger:

i.
B544248

Disconnect the connector.



b.
B537106C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



c.
B537107C01
1.74,0.479 2.083,0.375 2.083,0.375 1.719,0.76 true 2.135,0.25 2.448,0.448 0.313,0.198 10 false *a
*a Matchmark


When reusing the back door glass:

i.

Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.


ii.

Install the suction cups to the back door glass.



d.
B537108C01
0.969,1.5 0.813,1.792 true 0.583,0.792 0.865,0.917 true 2.771,0.771 2.5,0.906 true 0.51,1.427 0.865,1.313 true 2.833,1.427 2.49,1.281 true 0.896,0.844 1.083,1.052 0.188,0.208 10 true *1 2.323,0.833 2.5,1.031 0.177,0.198 10 true *2 0.667,1.823 0.979,2.021 0.313,0.198 10 true *a 0.906,1.198 1.094,1.406 0.188,0.208 10 true *3 2.302,1.198 2.49,1.406 0.188,0.208 10 true *4
*1 Back Window Glass Clip LH
*2 Back Window Glass Clip RH
*3 No. 2 Back Door Glass Spacer
*4 No. 1 Back Door Glass Spacer
*a Piano Wire


From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



f.

Cut through the adhesive by pulling the piano wire around the back door glass.


g.

Using suction cups, disconnect the No. 1 back door glass spacer and the No. 2 back window glass spacer and remove the back door glass.

NOTICE:

Do not drop the back door glass.