The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during No. 1 slide door weatherstrip RH removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
Use the same procedure described for the RH side.
1. PRECAUTION (w/ Rear Curtain Shield Airbag)
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Curtain Shield Airbag)
Click hereGeneral>MAINTENANCE>1GD-FTV BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
74733
3.REMOVE NO. 1 HAND GRIP COVER (for Full Cover Type, w/ Hand Rail)
74708
4.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for Full Cover Type, w/ Hand Rail)
67917C
5.REMOVE REAR DOOR SCUFF PLATE RH (for Full Cover Type)
68394A
6.REMOVE SLIDE DOOR LOWER RAIL PLATE RH (w/o Power Slide Door)
|
Remove in this Direction |
Remove the bolt.
Detach the guide and remove the slide door lower rail plate RH as shown in the illustration.
68394A
7.REMOVE SLIDE DOOR LOWER RAIL PLATE RH (w/ Power Slide Door)
|
Remove in this Direction |
Remove the clip and slide door lower rail plate RH as shown in the illustration.
51078D
8.REMOVE SIDE STEP BRACKET SUB-ASSEMBLY RH (w/ Power Slide Door, for Standard Roof)
|
Bolt |
|
Ground Bolt |
Remove the 2 ground bolts and disconnect the 2 ground wires.
Remove the 3 bolts and side step bracket sub-assembly RH.
51078D
9.REMOVE SIDE STEP BRACKET SUB-ASSEMBLY RH (w/ Power Slide Door, for High Roof)
|
Bolt |
|
Ground Bolt |
Remove the 2 ground bolts and disconnect the 2 ground wires.
Remove the 3 bolts and side step bracket sub-assembly RH.
51079F
10.REMOVE SIDE STEP BRACKET SUB-ASSEMBLY LH (w/ Power Slide Door, w/ Hand Rail)
|
Bolt |
|
Ground Bolt |
Remove the 2 ground bolts and disconnect the 2 ground wires.
Remove the 4 bolts and side step bracket sub-assembly LH.
67871E
11.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
|
Ground Bolt |
|
Connector |
Disconnect the wire harness (w/o Power Slide Door).
Remove the ground bolt and disconnect the ground wire.
Disconnect the 2 connectors.
Disconnect the wire harness (w/ Power Slide Door).
Disconnect the 4 connectors.
|
Remove in this Direction |
Disconnect the wire harness protector.
Remove the bolt.
Detach the clip and disconnect the wire harness protector as shown in the illustration.
w/ Power Slide Door:
Move the slide door RH so that the 2 bolts are visible as shown in the illustration.
Remove the 2 bolts and disconnect the roller part of the lower slide door roller arm RH from the slide door motor unit RH.
| *a | Cutout |
Rotate the roller part of the slide door lower roller arm sub-assembly RH clockwise to disconnect the slide door lower roller arm sub-assembly RH from the cutout of the rear floor step assembly RH.
Support the lower portion of the slide door RH when disconnecting the slide door lower roller arm sub-assembly RH, as the slide door RH becomes unstable.
Work with 2 or more persons when disconnecting the slide door RH in order to prevent deformation and damage.
for Standard Roof:
Remove the No. 1 slide door weatherstrip RH.
for High Roof:
Remove the No. 1 slide door weatherstrip RH.
When removing, make sure that non-drying sealer does not adhere to the body and slide door.