Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P010516  Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Below Threshold  P010517  Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Above Threshold  


DESCRIPTION

Refer to DTC P010512.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P010512

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010516 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Below Threshold Manifold absolute pressure sensor output is 0 V or less for 10 seconds when the accelerator opening amount is 15% or more (2 trip detection logic).
·

Vacuum hose connection

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0106
P010517 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Above Threshold Manifold absolute pressure sensor output is 4.9 V or higher for 10 seconds when idling the engine after warming it up (2 trip detection logic).
·

Vacuum hose connection

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0106

Related Data List
DTC No. Data List
P010516
P010517
Intake Manifold Absolute Pressure

HINT:

If DTC P010516 and/or P010517 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P010516
P010517
After warming up engine, idle engine for 10 seconds or more, and then drive vehicle under load (accelerator opening amount 15% or more) for 10 seconds

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P010516 OR P010517)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P010516 or P010517 is output A
DTC P010516 or P010517 and other DTCs are output B




A

2.CHECK VACUUM HOSE CONNECTIONS

B

2.CHECK VACUUM HOSE CONNECTIONS
a.

Check the vacuum hose connections.

OK:

Vacuum hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CONNECT HOSE CORRECTLY
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After warming up the engine, idle the engine for 10 seconds or more, and then drive the vehicle under load (accelerator opening angle 15% or more) for 10 seconds or more.


f.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P010516 or P010517.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, drive the vehicle for 5 minutes, idle the engine for 5 minutes, and then check "All Readiness" again.



Result:
Proceed to
NEXT



NEXT

END

5.CONNECT HOSE CORRECTLY
Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED