Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P033511  Crankshaft Position Sensor "A" Circuit Short to Ground  P033515  Crankshaft Position Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P03351F.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P03351F

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0338

HINT:

If DTC P033511 or P033515 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




Reference: Inspection using an oscilloscope.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

The correct waveform is as shown.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P033511
P033515
Ignition switch ON for 4 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Record any output DTC(s).


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

f.

Turn the ignition switch off for 30 seconds or more.


g.

Disconnect the crankshaft position sensor connector.


h.

Turn the ignition switch to ON for 4 seconds or more.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Check whether the DTC changes when the connector is disconnected and connected.

Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)

B

5.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)
a.
A372026C59
1.729,0.833 2.146,1.083 0.417,0.25 1.698,2.229 2.021,1.635 true 2.385,2.24 2.073,1.646 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.823,0.875 2.281,1.073 0.458,0.198 10 false E8 1.198,2.313 1.979,2.51 0.781,0.198 10 false 20 (VCNE) 2.229,2.313 2.823,2.51 0.594,0.198 10 false 19 (NE-)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E8-20 (VCNE) - E8-19 (NE-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E104-1 (NE+) - E8-28 (NE+) Always Below 1 Ω
E104-2 (NE-) - E8-19 (NE-) Always Below 1 Ω
E104-1 (NE+) or E8-28 (NE+) - Body ground and other terminals Always 10 kΩ or higher
E104-2 (NE-) or E8-19 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the crankshaft position sensor connector.


b.
A372026C60
1.729,0.833 2.146,1.083 0.417,0.25 1.417,2.219 2.021,1.635 true 2.052,2.229 2.073,1.646 true 2.563,2.229 2.125,1.688 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.823,0.875 2.281,1.073 0.458,0.198 10 false E8 0.865,2.313 1.646,2.51 0.781,0.198 10 false 20 (VCNE) 1.729,2.313 2.323,2.51 0.594,0.198 10 false 19 (NE-) 2.448,2.313 3.094,2.521 0.646,0.208 10 false 28 (NE+)
*a Component with harness connected
(ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E8-20 (VCNE) - E8-28 (NE+) Ignition switch off No short or no open circuit
E8-28 (NE+) - E8-19 (NE-) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE CRANKSHAFT POSITION SENSOR

NG

7.REPLACE ECM
5.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END