Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P226300  Turbocharger/Supercharger Boost System Performance  


DESCRIPTION

After the ignition switch is turned off, the ECM performs nozzle vane plate soot removal control (current opening angle→fully opened→fully closed). Monitor the motor drive current value while these opening and closing operations are performed. If the value exceeds the threshold, it can be determined that movement is abnormal. If the system judges that abnormal movements have occurred twice, this DTC is stored, and a message is displayed on the multi-information display the next time the ignition switch is turned to ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P226300 Turbocharger/Supercharger Boost System Performance During soot removal control of the nozzle vane plate after the ignition switch is turned off, DC motor operation current exceeds the threshold (2 trip detection logic). Abnormality in sliding movement of turbocharger nozzle vane plate Does not come on*
*: The multi-information display illuminates.
DTC stored SAE Code: P2263

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P226300 Turn the ignition switch off, and then perform turbocharger nozzle vane plate soot removal control.

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (DTC P226300)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read DTCs.

Result:
Result Proceed to
DTC P226300 is output A
DTC P226300 and other DTCs are output B




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)

B

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature is 77°C (170°F) or higher with all the accessories switched off.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo Cleaning.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo Cleaning
50004 372 42021

e.

Perform the Active Test.

HINT:
·

VN turbo cleaning finishes 20 minutes after the speed increases.

·

If actions such as depressing the accelerator pedal or operating the shift lever are performed, cleaning control is stopped. If this occurs, it is necessary to perform the procedure again.




Result:
Proceed to
NEXT



NEXT

3.INSPECT COMBINATION METER DISPLAY (MULTI-INFORMATION DISPLAY)
3.INSPECT COMBINATION METER DISPLAY (MULTI-INFORMATION DISPLAY)
a.

Turn the ignition switch off and wait for at least 30 seconds.


b.

Turn the ignition switch to ON.


c.

Check the multi-information display.

Result:
Result Proceed to
Message displayed in multi-information display A
Message not displayed in multi-information display B




A

4.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

5.CLEAR DTC
4.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Turn the ignition switch off and wait for at least 30 seconds.


b.

Turn the ignition switch to ON.


c.

Check that a message is not displayed in the multi-information display.


d.

Connect the GTS to the DLC3.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes / Clear.

Powertrain > Engine > Clear DTCs
50002 372

g.

Clear the DTC.


Result:
Proceed to
NEXT



NEXT

END