Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079307 1GD-FTV INTAKE / EXHAUST _0385721 EXHAUST MANIFOLD W/ TURBOCHARGER A

1GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the turbocharger sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger nozzle vane control actuator


Perform initialization -
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR:

(Click here)

·

w/o EGR Cooler:

(Click here)



CAUTION:
·
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 12601B 1.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 25051 2.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 17167 3.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)

Hide 17271 4.REMOVE NO. 1 TURBO INSULATOR (w/o EGR Cooler)

Hide 5.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

Hide 6.REMOVE EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

Hide 17291 7.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)

Hide 51406A 8.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

Hide 52618 9.REMOVE LOWER FRONT BUMPER ABSORBER

Hide 51405A 10.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 11.DRAIN ENGINE COOLANT

Hide 12.DRAIN ENGINE COOLANT (for Water Cooled Type Intercooler)

Hide 17940D 14.REMOVE INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 17030 15.REMOVE AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)

Hide 25761B 16.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)

Hide 17303T 17.REMOVE AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)

Hide 53106B 18.REMOVE RADIATOR COVER SUB-ASSEMBLY

Hide 17751 19.REMOVE NO. 1 AIR CLEANER INLET

Hide 44360 20.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16640 21.REMOVE INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16470 22.REMOVE RADIATOR RESERVE TANK ASSEMBLY

Hide 16571C 23.REMOVE NO. 1 RADIATOR HOSE

Hide 16552C 24.REMOVE NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 165A0 25.REMOVE NO. 1 INTERCOOLER COOLING WATER HOSE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 161B0 26.REMOVE ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16515A 27.DISCONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16711 28.REMOVE FAN SHROUD

Hide 17705 29.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.
A438470

Disconnect the mass air flow meter sub-assembly connector and detach the harness clamp.


b.
A438145C01
0.708,0.833 0.948,1.021 0.24,0.188 10 true *a 0.656,1.667 0.896,1.854 0.24,0.188 10 true *a
*a Air Cleaner Cap Clamp


Detach the 2 air cleaner cap clamps.


c.
A438146

Detach the 2 guides and disconnect the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


d.
A438147

Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.


Hide 17801 30.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case.


Hide 17701 31.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A438471

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 32.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 87120G 33.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

Hide 16279 34.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A352791

for Cold Area Specification Vehicles:

Slide the 2 hose clips and remove the water hose from the compressor inlet elbow and No. 3 water by-pass pipe.


b.
A359575C01
0.042,0.052 0.354,0.208 0.313,0.156 10 false *A 0.083,2.313 0.396,2.469 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Slide the 2 hose clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe sub-assembly.


c.

Remove the bolt and No. 3 water by-pass pipe.


Hide 12229 35.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

a.
A438149

for Air Cooled Type Intercooler:

i.

Slide the 2 hose clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.


ii.

Slide the hose clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.


iii.
A438150

Remove the bolt and disconnect the PCV pipe from the compression outlet elbow.


iv.
A438151

Slide the 2 hose clips and remove the PCV pipe.



b.
A446458

for Water Cooled Type Intercooler:

i.

Slide the 2 hose clips and disconnect the No. 20 water by-pass hose from the PCV pipe and No. 1 water by-pass pipe.


ii.

Slide the hose clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.


iii.
A446459

Remove the 2 bolts and disconnect the PCV pipe from the compression outlet elbow.


iv.
A446460

Slide the 2 hose clips and remove the PCV pipe.



Hide 12261 36.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

a.
A438152

Slide the 2 hose clips, detach the clamp and remove the PCV hose.


Hide 37.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

a.
A438159

Slide the 2 hose clips and disconnect the No. 21 water by-pass hose from the turbocharger sub-assembly and No. 1 water by-pass pipe.


b.
A438160

Slide the 2 hose clips and disconnect the No. 4 turbo water hose from the turbocharger sub-assembly and No. 1 turbo water pipe sub-assembly.


Hide 16268 38.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 39.DISCONNECT TURBO WATER HOSE

a.
A359576C01
0.052,0.083 0.365,0.24 0.313,0.156 10 true *A 0.063,2.344 0.375,2.5 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.


Hide 40.DISCONNECT BRACKET OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)

a.
A353408

Remove the bolt and disconnect the oil cooler tube bracket.


b.
A438472

Remove the bolt and disconnect the wire harness.


Hide 41.DISCONNECT WIRE HARNESS CLAMP BRACKET (for Manual Transmission)

a.
A438472

Remove the bolt and disconnect the wire harness.


Hide 87101 42.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

a.
A360493

Remove the bolt, detach the clamp and disconnect the wire harness.


b.
A360494

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly.


Hide 17293 43.REMOVE TURBOCHARGER STAY

a.
A344955

Remove the 3 bolts, nut and turbocharger stay.


Hide 15474 44.REMOVE TURBO OIL OUTLET PIPE

a.
A344956

Slide the 2 hose clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.


b.

Remove the 2 bolts, turbo oil outlet pipe and gasket.


Hide 15407 45.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A344957

Remove the union bolt and gasket.


b.
A344958

Remove the 2 nuts and turbo oil inlet pipe sub-assembly.

NOTICE:
A344974E01
0.667,0.531 0.823,0.729 0.156,0.198 10 true A

Do not loosen the nut labeled A.



c.

Remove the gasket.


Hide 17201 46.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A359577C01
0.052,0.031 0.365,0.188 0.313,0.156 10 true *A 0.083,2.292 0.396,2.448 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Remove the 3 nuts and turbocharger sub-assembly.


b.

Remove the gasket from the exhaust manifold.


Hide 25601 47.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 25601 48.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

Hide 25617 49.REMOVE EGR HOLE COVER PLATE (w/o EGR System)

a.
A408312

Remove the 2 nuts, EGR hole cover plate and gasket.


b.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts shown in the illustration.


Hide 17141 50.REMOVE EXHAUST MANIFOLD

a.
A359578C01
0.083,0.094 0.396,0.25 0.313,0.156 10 true *A 0.094,2.354 0.406,2.51 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.


b.

Remove the gasket.


Hide 16027 51.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A359579C01
0.042,0.083 0.354,0.24 0.313,0.156 10 true *A 0.073,2.479 0.385,2.635 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


except Water Cooled Compressor Housing Turbocharger:

Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.


b.
A438153C01
0.042,0.083 0.354,0.24 0.313,0.156 10 true *A 0.073,2.479 0.385,2.635 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


for Water Cooled Compressor Housing Turbocharger:

Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.


c.

Remove the bolt.


d.
A425660C02
0.094,0.042 0.406,0.198 0.313,0.156 10 false *A 0.115,2.271 0.427,2.427 0.313,0.156 10 false *B
*A except Water Cooled Compressor Housing Turbocharger
*B for Water Cooled Compressor Housing Turbocharger


Remove the 2 nuts, No. 1 turbo water pipe sub-assembly and gasket.


Hide 17274 52.REMOVE COMPRESSOR INLET ELBOW

a.
A438154C01
0.073,0.073 0.385,0.229 0.313,0.156 10 false *A 0.115,2.188 0.427,2.344 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Remove the 2 bolts and compressor inlet elbow stay.


b.
A438155C02
0.052,0.063 0.406,0.292 0.354,0.229 10 true *A 0.094,2.229 0.406,2.385 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


except Water Cooled Compressor Housing Turbocharger:

Remove the 2 nuts and compressor inlet elbow from the turbocharger sub-assembly.


c.
A438161C01
0.052,0.063 0.406,0.292 0.354,0.229 10 true *A 0.094,2.229 0.406,2.385 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


for Water Cooled Compressor Housing Turbocharger:

Remove the 2 nuts and compressor inlet elbow from the turbocharger sub-assembly.


d.
A438156C01
0.042,0.042 0.354,0.198 0.313,0.156 10 true *A 0.115,2.229 0.427,2.385 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


except Water Cooled Compressor Housing Turbocharger:

Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow and gasket.


e.

for Water Cooled Compressor Housing Turbocharger:

i.
A438162C01
0.042,0.042 0.354,0.198 0.313,0.156 10 true *A 0.115,2.229 0.427,2.385 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow.


ii.
A438163

Remove the gasket from the compressor inlet elbow.



Hide 17275 53.REMOVE COMPRESSOR OUTLET ELBOW

a.
A438157C01
0.083,0.063 0.396,0.219 0.313,0.156 10 false *A 0.156,2.25 0.469,2.406 0.313,0.156 10 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


for Air Cooled Type Intercooler:

i.

Remove the 2 nuts and compressor outlet elbow.


ii.

Remove the gasket.


iii.
A438158

except Cold Area Specification Vehicles:

Remove the bolt and hose clamp.



b.
A446467

for Water Cooled Type Intercooler:

i.

Remove the 2 nuts and compressor outlet elbow.


ii.

Remove the gasket.



Hide 54.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A344968

Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.


b.
A344969

Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.


c.
A344970

Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.