Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P107F62  Fuel Rail Pressure Sensor "A"/"B" Signal Compare Failure  


DESCRIPTION

Refer to DTC P008700.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P008700

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P107F62 Fuel Rail Pressure Sensor "A"/"B" Signal Compare Failure The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored SAE Code: P107F

Related Data List
DTC No. Data List
P107F62
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)

·

Fuel Pressure (Low) / Fuel Pressure 2



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P107F62 Idling for 1 second or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (TARGET FUEL PRESSURE (HIGH), FUEL PRESSURE (HIGH) AND FUEL PRESSURE (LOW) / FUEL PRESSURE 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High), Fuel Pressure (High) and Fuel Pressure (Low) / Fuel Pressure 2.

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (High)
Fuel Pressure (High)
Fuel Pressure (Low) / Fuel Pressure 2
50003 372 264,265,267

d.

Start the engine.


e.

Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.

Result:
Result Proceed to
Fuel Pressure (High) or Fuel Pressure (Low) / Fuel Pressure 2 is always 10000 kPag or less
or
Fuel Pressure (High) or Fuel Pressure (Low) / Fuel Pressure 2 is always 220000 kPag or higher
A
Except above B


HINT:

Normally, "Fuel Pressure (High)" is within 5000 kPag of "Target Fuel Pressure (High)".




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P107F62)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E105-5 (PR) - E7-18 (PCR1) Always Below 1 Ω
E105-2 (PR2) - E8-23 (PCR2) Always Below 1 Ω
E105-1 (VCS) - E8-22 (VCS) Always Below 1 Ω
E105-6 (VC) - E7-28 (VCM) Always Below 1 Ω
E105-4 (E2) - E7-19 (E2M) Always Below 1 Ω
E105-3 (E2S) - E8-21 (E2S) Always Below 1 Ω
E105-5 (PR) or E7-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
E105-2 (PR2) or E8-23 (PCR2) - Body ground and other terminals Always 10 kΩ or higher
E105-1 (VCS) or E8-22 (VCS) - Body ground and other terminals Always 10 kΩ or higher
E105-6 (VC) or E7-28 (VCM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMON RAIL ASSEMBLY

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P107F62)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P107F62)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Read the DTCs.

Result:
Result Proceed to
DTC P107F62 is output A
No DTC is output B




A

5.REPLACE COMMON RAIL ASSEMBLY

B

END

5.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P107F62)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P107F62)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Read the DTCs.

Result:
Result Proceed to
DTC P107F62 is output A
No DTC is output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Let the engine idle for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END