Home › Engine / Hybrid System › 1GD-FTV (FUEL) › COMMON RAIL
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385714 COMMON RAIL A

1GD-FTV FUEL  COMMON RAIL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the common rail assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 25800 3.REMOVE EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 25800 4.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler)

Hide 25624 5.REMOVE EGR VALVE ADAPTER (w/o EGR Cooler)

Hide 23804D 7.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23815D 8.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 9.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 10.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 11.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23282H 12.REMOVE NO. 4 FUEL HOSE

a.
A344943

Slide the clamp and disconnect the No. 4 fuel hose from the common rail assembly.


Hide 23810A 13.REMOVE COMMON RAIL ASSEMBLY

a.
A344944

Detach the wire harness clamp.


b.

Disconnect the fuel pressure sensor connector from the common rail assembly.


c.
A344945

Remove the 2 nuts and common rail assembly.

NOTICE:

Do not remove the pressure discharge valve or fuel pressure sensor.