Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P225D2A  NOx Sensor Performance - Signal Biased/Stuck Low Bank 1 Sensor 1 Signal Stuck In Range  


DESCRIPTION

The ECM estimates the amount of NOx expelled while the engine is operating and compares the estimated integrated value of change for the NOx value and the integrated value of the No. 1 nitrogen oxides sensor based on actual output values.

When the actual integrated change value of the No. 1 nitrogen oxides sensor output does not significantly change but the NOx integrated value for the estimated amount of change reaches the specified value, the system judges that the No. 1 nitrogen oxides sensor is stuck and outputs a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P225D2A NOx Sensor Performance - Signal Biased/Stuck Low Bank 1 Sensor 1 Signal Stuck In Range When the actual integrated change value of the No. 1 nitrogen oxides sensor output does not significantly change but the NOx integrated value for the estimated amount of change reaches the specified value.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC Stored SAE Code: P225D

Related Data List
DTC No. Data List
P225D2A
·

NOx Corrected Density B1S1

·

Fr-NOx Sensor NOx Active Status (SCU)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P225D2A After warming up the engine, alternate between idling and racing the engine under no load approximately 30 times.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P225D2A)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P225D2A is output A
DTC P225D2A and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING GTS (FR-NOX SENSOR NOX ACTIVE STATUS (SCU) AND NOX CORRECTED DENSITY B1S1)

B

2.READ VALUE USING GTS (FR-NOX SENSOR NOX ACTIVE STATUS (SCU) AND NOX CORRECTED DENSITY B1S1)
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / NOx Corrected Density B1S1 and Fr-NOx Sensor NOx Active Status (SCU).

Powertrain > Engine > Data List
Tester Display
NOx Corrected Density B1S1
Fr-NOx Sensor NOx Active Status (SCU)
50003 372 1169,1043

e.

Check that the No. 1 nitrogen oxides sensor is activated.

HINT:

If the "Fr-NOx Sensor NOx Active Status (SCU)"is ON, the No. 1 nitrogen oxides sensor is active.



f.

Alternate between idling and racing the engine under no load and check that the "NOx Corrected Density B1S1" value changes.

OK:

The "NOx Corrected Density B1S1" value changes. (Increases when engine is raced under no load, decreases when idling)


HINT:
·

Normal output is approximately 100 ppm at the maximum possible engine speed under no load.

·

It is easier to check the amount of "NOx Corrected Density B1S1" change by displaying a graph on the GTS.




Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 NITROGEN OXIDES SENSOR

NG

REPLACE NO. 1 NITROGEN OXIDES SENSOR

3.INSPECT NO. 1 NITROGEN OXIDES SENSOR
a.

Check for open or short circuits, or damage to the sensor control unit of the No. 1 nitrogen oxides sensor and the detection component wire harness.

OK:

No open or short circuit malfunction.



Result:
Proceed to
OK
NG



OK

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

REPLACE NO. 1 NITROGEN OXIDES SENSOR

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Alternate between idling and racing the engine under no load approximately 30 times.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P225D2A.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, alternate between idling and racing the engine under no load approximately 30 times again.



Result:
Proceed to
NEXT



NEXT

END