The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.
The normal signal conditions are as shown in the table below.
| Signal (ECM Terminal) | Brake Pedal Released | In Transition | Brake Pedal Depressed |
|---|---|---|---|
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
[OFF] denotes ground potential.
[ON] denotes battery potential (+B).
On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P05042B | Brake Switch "A"/"B" Signal Cross Coupled | Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON. (b) STP signal OFF when ST1- signal is off. |
·
Open or short in stop light switch signal circuit ·
Stop light switch assembly ·
ECM |
Does not come on | DTC stored | SAE Code: P0504 |
| DTC No. | Data List |
|---|---|
| P05042B | Stop Light SW |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P05042B | Depress and release brake pedal with ignition switch ON |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Stop light switch conditions can be checked using the GTS.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.
Check Stop Light SW when the brake pedal is depressed and released.
| Brake Pedal Operation | Specified Condition |
|---|---|
| Depressed | ON |
| Released | OFF |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
| *A | for LED Type |
| *B | for Bulb Type |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-7 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M1-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LED Type |
| *B | for Bulb Type |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M1-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK (for LED Type) | A |
| OK (for Bulb Type) | B |
| NG | C |
A
B
C
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Brake Pedal Depressed |
| *b | Brake Pedal Released |
| *c | Component with harness connected
(ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Operation | Specified Condition |
|---|---|---|
| A2-12 (ST1-) - Body ground | Released | 7.5 to 14 V |
| Depressed | Below 1.5 V | |
| A2-13 (STP) - Body ground | Released | Below 1.5 V |
| Depressed | 7.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the stop light switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-5 (L) - A2-12 (ST1-) | Always | Below 1 Ω |
| M2-3 (L) - A2-13 (STP) | Always | Below 1 Ω |
| M2-5 (L) or A2-12 (ST1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| M2-3 (L) or A2-13 (STP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M1-3 (L) - A2-12 (ST1-) | Always | Below 1 Ω |
| M1-1 (L) - A2-13 (STP) | Always | Below 1 Ω |
| M1-3 (L) or A2-12 (ST1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| M1-1 (L) or A2-13 (STP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG