When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the N19 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N19-5 (CANH) - N19-4 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3A, 3B and 3D instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/o Stop and Start System |
||
| 3D-29 - 3B-23 | Always | Below 1 Ω |
| 3A-15 - 3D-35* | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-11 (GND1) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||
| A-31 (BECU) - Body ground | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| A-32 (IG) - Body ground | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 3A, 3B, 3C, 3E*1 or 3G*2 instrument panel junction block assembly connectors.
*1: for LHD
*2: for RHD
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-3 - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for LHD *2: for RHD |
||
| 3C-1 - Body ground | Always | 11 to 14 V |
| 3E-1 - Body ground*1 | Always | 11 to 14 V |
| 3G-1 - Body ground*2 | Always | 11 to 14 V |
| 3A-30 - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-15 - Body ground | Ignition switch ACC | 10.5 to 16 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>Backup Boost Converter Circuit
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-17 - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG