22204
1.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY (for Air Cooled Type Intercooler)
Read the value of Data List item "Mass Air Flow Sensor" using the GTS.
Perform the inspection of the intake mass air flow meter sub-assembly while it is installed to the air cleaner cap sub-assembly (installed to the vehicle).
Check and ensure the following conditions:
Turn off all electrical loads, such as the air conditioning, etc.
Check that the coolant temperature is 75°C (167°F) or more.
Put the shift lever in the N position.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
w/o Exhaust Gas Temperature Sensor for EGR:
According to the display on the GTS, read the Data List when the engine is running.
| Tester Display |
|---|
| Mass Air Flow Sensor |
w/ Exhaust Gas Temperature Sensor for EGR:
According to the display on the GTS, read the Data List when the engine is running.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the value on the GTS.
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DATA LIST / ACTIVE TEST
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DATA LIST / ACTIVE TEST
If the result is not as specified, clean the intake mass air flow meter sub-assembly.
After cleaning (air blowing) the intake mass air flow meter sub-assembly, perform an on-vehicle inspection of the intake mass air flow meter sub-assembly again and replace the intake mass air flow meter sub-assembly if the result is not as specified.
If the result is within the specified range, check the intake air temperature sensor (thermistor) resistance.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION
22204
2.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY (for Water Cooled Type Intercooler)
Read the value of Data List item "Mass Air Flow Sensor" using the GTS.
Perform the inspection of the intake mass air flow meter sub-assembly while it is installed to the air cleaner cap sub-assembly (installed to the vehicle).
Check and ensure the following conditions:
Turn off all electrical loads, such as the air conditioning, etc.
Check that the coolant temperature is 75°C (167°F) or more.
Put the shift lever in the N position.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
According to the display on the GTS, read the Data List when the engine is running.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the value on the GTS.
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DATA LIST / ACTIVE TEST
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DATA LIST / ACTIVE TEST
for Water Cooled Type Intercooler:
If the result is not as specified, clean the intake mass air flow meter sub-assembly.
After cleaning (air blowing) the intake mass air flow meter sub-assembly, perform an on-vehicle inspection of the intake mass air flow meter sub-assembly again and replace the intake mass air flow meter sub-assembly if the result is not as specified.
If the result is within the specified range, check the intake air temperature sensor (thermistor) resistance.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION
22204
3.CLEAN INTAKE MASS AIR FLOW METER SUB-ASSEMBLY
If the intake mass air flow meter sub-assembly is removed and installed 10 times or more, the thread of the hole of the intake mass air flow meter sub-assembly may be damaged. Therefore, do not loosen the screws of the intake mass air flow meter sub-assembly.
Remove the air cleaner cap sub-assembly.
| *1 | Intake Mass Air Flow Meter Sub-assembly |
| *a | Air Blow Gun |
| *b | 10 mm (0.394 in.) |
| *c | Airflow Hole |
Clean the intake mass air flow meter sub-assembly.
Do not contact the intake mass air flow meter sub-assembly with the nozzle of the air blow gun.
Do not insert the nozzle of the air blow gun into the airflow hole.
| *a | Air Blow Duration |
| *b | 3 to 6 Seconds |
| *c | 1 Second |
| *d | Air Blowing |
| *e | Air Stopped |
Using an air blow gun, clean the hole of the intake mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the airflow hole at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi).
Apply 5 intermittent bursts of air to the airflow hole at 2 locations.
Install the air cleaner cap sub-assembly.