Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTERCOOLER › from 2021.07
RM35X0E _51 Engine / Hybrid System _079307 1GD-FTV INTAKE / EXHAUST _0385722 INTERCOOLER A

1GD-FTV INTAKE / EXHAUST  INTERCOOLER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL GROMMET

a.

Install the 2 grommets to the lower radiator support assembly.


Hide 17940D 2.INSTALL INTERCOOLER ASSEMBLY

a.
A438469

Attach the 2 guides and install the intercooler assembly to the lower radiator support assembly.


Hide 88689E 3.INSTALL NO. 1 COOLER BRACKET

a.
A438467

Install the No. 1 cooler bracket to the radiator support assembly with the 4 nuts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Install the intercooler assembly to the No. 1 cooler bracket with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 17942 4.INSTALL NO. 2 INTERCOOLER AIR GUIDE

a.
A438466

Attach the claws to install the No. 2 intercooler air guide.


Hide 17941 5.INSTALL NO. 1 INTERCOOLER AIR GUIDE

a.
A438178

Attach the claws to install the No. 1 intercooler air guide.


Hide 17312B 6.INSTALL NO. 2 AIR INLET DUCT

a.
A438177

for RH Side:

Attach the claws to install the No. 2 air inlet duct.


b.
A438465

for LH Side:

Attach the claws to install the No. 2 air inlet duct.


Hide 44402 7.CONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY

a.
A438175

for LHD:

Connect the No. 1 power steering oil cooler sub-assembly with the 3 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


b.
A438176

for RHD:

Connect the No. 1 power steering oil cooler sub-assembly with the 4 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 53287B 8.INSTALL RADIATOR SUPPORT EXTENSION RH

a.
A438173C01
0.073,0.042 0.385,0.198 0.313,0.156 10 true *A 0.094,2.375 0.406,2.531 0.313,0.156 10 false *B
*A for LHD
*B for RHD


Attach the claws to install the radiator support extension RH.


Hide 53288B 9.INSTALL RADIATOR SUPPORT EXTENSION LH

a.
A438171C01
0.073,0.042 0.385,0.198 0.313,0.156 10 true *A 0.094,2.375 0.406,2.531 0.313,0.156 10 false *B
*A for LHD
*B for RHD


Attach the claws to install the radiator support extension LH.


Hide 17303T 10.INSTALL AIR PIPE SUB-ASSEMBLY

a.
A483557C01
1.031,2.229 1.583,2.167 true 2.333,0.781 2.594,0.958 2.594,0.958 2.708,0.958 true 2.354,0.208 2.469,0.208 2.469,0.208 2.75,0.469 true 2.385,1.615 2.5,1.615 2.5,1.615 2.854,1.198 true 1.865,2.167 2.417,2.24 true 2.75,0.865 2.958,1.042 0.208,0.177 10 false *a 2.188,0.135 2.5,0.292 0.313,0.156 10 false *b 1.646,2.063 1.958,2.219 0.313,0.156 10 false *c 2.198,1.521 2.406,1.698 0.208,0.177 10 false *a
*a Protrusion
*b Groove
*c Retainer


Install the air pipe sub-assembly to the intake air connector and intercooler assembly and lock the retainers.

NOTICE:
·

Securely insert the retainer so that the locks are engaged. Then, pull and check that the locks are engaged and that the hose cannot be pulled out.

·

Align the protrusion with the groove of the intake air connector.



HINT:
A483558C01
0.99,2.708 0.969,2.5 0.969,2.5 0.771,2.5 true 2.469,2.667 2.458,2.458 2.458,2.458 2.26,2.458 true 1.146,3.104 1.146,2.927 true 2.792,3.073 2.792,2.896 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a 2.365,1.906 2.677,2.063 0.313,0.156 10 false *b 0.583,2.385 0.781,2.583 0.198,0.198 10 true *c 2.063,2.354 2.26,2.552 0.198,0.198 10 true *c 1.063,3.125 1.26,3.323 0.198,0.198 10 true *d 2.688,3.094 2.885,3.292 0.198,0.198 10 true *d
*a Correct
*b Incorrect
*c Retainer End
*d Stopper


Make sure that the retainer end contacts the stopper as shown in the illustration.



Hide 25761B 11.CONNECT NO. 1 VACUUM TRANSMITTING HOSE

a.
A483555

for Diesel Throttle Body Side:

Attach the 5 clamps and connect the No. 1 vacuum transmitting hose to the intercooler assembly, and slide the clip to secure the hose to the engine oil dipstick guide.


b.
A438168

for Intercooler Assembly Side:

Connect the No. 1 vacuum transmitting hose to the intercooler assembly, and slide the clip to secure the hose.


Hide 17030 12.INSTALL AIR HOSE ASSEMBLY

a.
A438170C01
0.823,2.073 1.135,2.229 0.313,0.156 10 false *a 2.396,2.01 2.708,2.167 0.313,0.156 10 false *b 2.469,2.188 2.781,2.344 0.313,0.156 10 false *c 2.708,2.344 3.021,2.5 0.313,0.156 10 false *d 2.635,0.99 2.854,1.156 0.219,0.167 10 true A 3.094,0.802 3.313,0.969 0.219,0.167 10 true B
*a 90°
*b 0 to 3 mm (0 to 0.118 in.)
*c 2 to 7 mm (0.0787 to 0.276 in.)
*d No Contact Hose Clamps


Connect the air hose assembly to the turbine outlet elbow with 2 new hose clamps as shown in the illustration.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

NOTICE:

Do not reuse the hose clamp.


HINT:

Make sure the hose clamp is oriented as shown in the illustration.



b.

Install the air tube support bracket with the 2 bolts to the air hose assembly and radiator support.

Torque:
for bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt B : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Connect the air hose assembly to the intercooler assembly and lock the retainer.

NOTICE:

Securely insert the retainer so that the locks are engaged. Then, pull and check that the locks are engaged and that the hose cannot be pulled out.


HINT:
A439809C01
1.031,2.667 0.969,2.5 0.969,2.5 0.771,2.5 true 2.521,2.625 2.458,2.458 2.458,2.458 2.26,2.458 true 1.115,3.073 1.115,2.896 true 2.771,3.073 2.771,2.896 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a 2.365,1.906 2.677,2.063 0.313,0.156 10 false *b 0.583,2.385 0.781,2.583 0.198,0.198 10 true *c 2.063,2.354 2.26,2.552 0.198,0.198 10 true *c 1.031,3.083 1.229,3.281 0.198,0.198 10 true *d 2.677,3.094 2.875,3.292 0.198,0.198 10 true *d
*a Correct
*b Incorrect
*c Retainer End
*d Stopper


Make sure that the retainer end contacts the stopper as shown in the illustration.



Hide 16546 13.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)

Hide 53209B 14.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

Hide 88590D 16.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)

Hide 86510 17.INSTALL HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)

Hide 86520 18.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 51466 19.INSTALL UPPER RADIATOR SUPPORT BRACE LH (for Wagon)

Hide 51465 20.INSTALL UPPER RADIATOR SUPPORT BRACE RH (for Wagon)

Hide 52021 21.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY