Home › Engine / Hybrid System › 1GD-FTV (COOLING) › RADIATOR › from 2020.05
RM35X0E _51 Engine / Hybrid System _079309 1GD-FTV COOLING _0386771 RADIATOR A

1GD-FTV COOLING  RADIATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 16535 1.INSTALL LOWER RADIATOR SUPPORT

a.
A442879

Install the 2 lower radiator supports to the radiator assembly.


Hide 16523A 2.INSTALL RADIATOR SUPPORT CUSHION

A442878

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16400 3.INSTALL RADIATOR ASSEMBLY

a.

w/ Air Conditioning System:

i.
A453702C02
0,0 0,0 false
V113147

Install in this Direction


Install the radiator assembly to the vehicle as shown in the illustration.

NOTICE:
·

Perform the following procedure with 2 or more people to prevent damage to the radiator assembly.

·

When installing the radiator assembly, do not damage the cooler condenser assembly.





b.

w/o Air Conditioning System:

i.
A453703C01
0,0 0,0 false
V113147

Install in this Direction


Install the radiator assembly to the vehicle as shown in the illustration.

NOTICE:

Perform the following procedure with 2 or more people to prevent damage to the radiator assembly.




Hide 32922A 4.CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)

a.

Connect the oil cooler outlet hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:

Make sure the oil cooler outlet hose is securely inserted to the stopper.


A442885C01
6.375,2.031 6.115,1.667 true 3.906,1.573 3.51,2.167 true 3.177,1.594 3.49,1.75 0.313,0.156 10 false *a 3.375,2.135 3.688,2.292 0.313,0.156 10 false *b 3.854,0.552 4.167,0.708 0.313,0.156 10 false *c 5.823,0.667 6.135,0.823 0.313,0.156 10 false *e 5.813,2.042 6.125,2.198 0.313,0.156 10 false *f 6.375,2.052 6.583,2.281 0.208,0.229 10 false *1 6.646,1.75 6.958,1.906 0.313,0.156 10 false *d 4.552,1.625 4.865,1.781 0.313,0.156 10 false *a 6.531,1.365 6.844,1.521 0.313,0.156 10 false *c
*1 Radiator Assembly - -
*a 45° *b Paint Mark
*c Upper Side *d Front Side
*e 0 to 3 mm (0 to 0.118 in.) *f 2 to 5 mm (0.0787 to 0.197 in.)



Hide 32921D 5.CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

a.

Connect the oil cooler inlet hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:

Make sure the oil cooler inlet hose is securely inserted to the stopper.


A442884C01
6.375,2.031 6.115,1.667 true 3.917,1.573 3.51,2.167 true 3.177,1.604 3.49,1.76 0.313,0.156 10 false *a 3.375,2.156 3.688,2.313 0.313,0.156 10 false *b 3.844,0.552 4.156,0.708 0.313,0.156 10 false *c 5.833,0.667 6.146,0.823 0.313,0.156 10 false *e 5.823,2.052 6.135,2.208 0.313,0.156 10 false *f 6.375,2.052 6.583,2.281 0.208,0.229 10 false *1 6.646,1.76 6.958,1.917 0.313,0.156 10 false *d 4.552,1.635 4.865,1.792 0.313,0.156 10 false *a 6.531,1.385 6.844,1.542 0.313,0.156 10 false *c
*1 Radiator Assembly - -
*a 45° *b Paint Mark
*c Upper Side *d Front Side
*e 0 to 3 mm (0 to 0.118 in.) *f 2 to 5 mm (0.0787 to 0.197 in.)



Hide 53205 6.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

for LHD:

i.
A442872C01
2.198,0.948 2.594,0.313 true 1.563,1.823 1.219,1.583 true 1.531,1.781 1.76,1.948 0.229,0.167 10 true *1 2.521,0.146 2.74,0.323 0.219,0.177 10 true *2
*1 Engine Room Main Wire
*2 Hood Lock Control Cable Assembly


Attach the clamps to connect the engine room main wire and hood lock control cable assembly.


ii.

Install the upper radiator support sub-assembly with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



b.

for RHD:

i.
A442873C01
0.271,1.427 0.719,0.875 true 1.51,1.729 1.208,1.573 true 1.51,1.698 1.729,1.896 0.219,0.198 10 true *1 0.115,1.396 0.344,1.573 0.229,0.177 10 true *2
*1 Engine Room Main Wire
*2 Hood Lock Control Cable Assembly


Attach the clamps to connect the engine room main wire and hood lock control cable assembly.


ii.

Install the upper radiator support sub-assembly with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



c.
A442871C01
0.917,1.417 1.135,0.865 true 0.76,1.417 0.969,1.594 0.208,0.177 10 true *1
*1 Engine Room Main Wire


Install the bolt to connect the engine room main wire.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 16546 7.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)

a.
A442870

Attach the guides to install the radiator protector.


b.

Install the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53209B 8.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

a.
A442869

Install the hood lock support brace sub-assembly with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

w/ Air Conditioning System:

i.
A442868C01
2.531,1.802 2.344,1.396 true 2.49,1.802 2.719,1.969 0.229,0.167 10 true *1
*1 Air Conditioner Tube and Accessory Assembly


Attach the clamp to connect the air conditioner tube and accessory assembly.



c.
A453739C01
2.583,0.552 3.063,0.823 true 3.104,0.823 3.302,1.021 0.198,0.198 10 true *1
*1 Engine Room Main Wire


for Wagon:

i.

Attach the clamps to connect the engine room main wire.



d.
A442867C01
2.177,0.979 2.792,0.677 true 2.771,0.563 2.979,0.729 0.208,0.167 10 true *1
*1 Engine Room Main Wire


except Wagon:

i.

Attach the clamps to connect the engine room main wire.


ii.

Connect the connector.



Hide 88590E 9.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)

Hide 86510 10.INSTALL HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)

Hide 86520 11.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 51466 12.INSTALL UPPER RADIATOR SUPPORT BRACE LH (for Wagon)

Hide 51465 13.INSTALL UPPER RADIATOR SUPPORT BRACE RH (for Wagon)

Hide 53285N 14.INSTALL RADIATOR SIDE AIR SEAL RH (for Wagon)

a.
A449478

Attach the claws to install the radiator side air seal RH.


Hide 53286F 15.INSTALL RADIATOR SIDE AIR SEAL LH (for Wagon)

a.
A449477

Attach the claw and clip to install the radiator side air seal LH.


Hide 17311B 16.INSTALL NO. 1 AIR INLET DUCT

a.
A442866

Attach the guides and claws to install the No. 1 air inlet duct.


b.

Install the clips.


Hide 16572D 19.INSTALL NO. 2 RADIATOR HOSE

a.

w/ Viscous Heater:

i.

Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 radiator hose paint mark is aligned with the protrusion of the water inlet.



A442887C01
5.865,2.115 5.052,2.219 true 6.5,0.75 5.885,0.594 true 4.271,0.563 3.958,1.219 true 3.344,0.385 3.656,0.542 0.313,0.156 10 false *a 3.292,0.885 3.604,1.042 0.313,0.156 10 false *b 4.229,0.396 4.542,0.552 0.313,0.156 10 false *c 3.844,0.521 4.156,0.677 0.313,0.156 10 false *d 6.5,1.24 6.813,1.396 0.313,0.156 10 false *e 6.281,1.854 6.594,2.01 0.313,0.156 10 false *f 6.531,0.656 6.74,0.885 0.208,0.229 10 false *g 0.635,1.052 0.771,1.24 0.135,0.188 10 true A 6.656,1.875 6.969,2.031 0.313,0.156 10 false *d 4.875,2.125 5.188,2.281 0.313,0.156 10 false *c
*a View A *b 135°
*c Paint Mark *d Front Side
*e Upper Side *f RH Side
*g Protrusion of the Water Inlet - -




b.

w/o Viscous Heater:

i.

Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 radiator hose paint mark is aligned with the protrusion of the water inlet.



A442886C02
5.865,2.094 5.052,2.198 true 6.49,0.75 5.875,0.594 true 4.26,0.563 3.948,1.219 true 3.313,0.51 3.625,0.667 0.313,0.156 10 false *a 4.531,1 4.844,1.156 0.313,0.156 10 false *b 4.229,0.406 4.542,0.563 0.313,0.156 10 false *c 3.844,0.531 4.156,0.688 0.313,0.156 10 false *d 6.5,1.25 6.813,1.406 0.313,0.156 10 false *e 6.292,1.865 6.604,2.021 0.313,0.156 10 false *f 6.531,0.656 6.74,0.885 0.208,0.229 10 false *g 0.656,1.052 0.792,1.24 0.135,0.188 10 true A 6.667,1.885 6.979,2.042 0.313,0.156 10 false *d 4.875,2.115 5.188,2.271 0.313,0.156 10 false *c
*a View A *b 180°
*c Paint Mark *d Front Side
*e Upper Side *f RH Side
*g Protrusion of the Water Inlet - -




c.

Install the No. 2 radiator hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 radiator hose paint mark is aligned with the protrusion of the radiator assembly.



A442888C01
5.5,0.604 4.854,0.719 true 6.188,2.417 5.521,2.281 true 3.948,1.635 3.688,2.271 true 3.26,0.438 3.573,0.594 0.313,0.156 10 false *a 4.188,2.01 4.5,2.167 0.313,0.156 10 false *b 3.573,2.26 3.885,2.417 0.313,0.156 10 false *c 3.885,2.219 4.198,2.375 0.313,0.156 10 false *d 4.667,1.229 4.979,1.385 0.313,0.156 10 false *e 1.979,1.073 2.115,1.26 0.135,0.188 10 true A 4.677,0.635 4.99,0.792 0.313,0.156 10 false *c 6.229,2.354 6.438,2.583 0.208,0.229 10 false *h 6.281,1.219 6.594,1.375 0.313,0.156 10 false *f 6.677,1.333 6.99,1.49 0.313,0.156 10 false *e 6.26,1.719 6.531,1.938 0.271,0.219 10 false *g
*a View A *b 90°
*c Paint Mark *d Lower Side
*e RH Side *f Upper Side
*g Front Side *h Protrusion of the Radiator Assembly



Hide 16711 20.INSTALL FAN SHROUD

a.

Install the fan pulley to the water pump assembly.


b.
A442862C01
0,0 0,0 false
V113147

Install in this Direction


Place the fan shroud together with the fan with fluid coupling assembly between the engine and radiator assembly.

NOTICE:

Do not allow the radiator assembly to interfere with other parts.



c.
A443596

Temporarily install the fan with fluid coupling assembly to the water pump assembly with the 4 nuts.

NOTICE:
·

Make sure to match the paint mark colors on the fan with fluid coupling assembly with the stud bolts of the same color on the water pump assembly.

·

When installing the fan and fan and generator V belt, make sure to securely tighten the nuts of the fan with fluid coupling assembly so that the fan pulley is properly aligned.




d.
A442860

Attach the guides to install the fan shroud.


e.

for Automatic Transmission:

i.
A442858

Attach the clamp to connect the oil cooler inlet hose.



f.
A442859

Attach the claws.


g.

Install the fan and generator V belt.

Click hereGeneral>MAINTENANCE>1GD-FTV DRIVE BELT>INSTALLATION


h.
A442857

Tighten the 4 nuts holding the fan with fluid coupling assembly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


i.
A453691

for Water Cooled Type Intercooler:

i.

Attach the clamps.



j.

Connect the No. 2 water by-pass hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 water by-pass hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 water by-pass hose paint mark is aligned with the protrusion of the radiator assembly.



A442881C01
5.333,0.844 6.031,0.646 true 5.729,2.229 5.167,2.354 true 4.208,2.281 3.969,1.656 true 0.906,1.042 1.604,1.271 true 3.281,0.5 3.594,0.656 0.313,0.156 10 false *a 3.594,2 3.906,2.156 0.313,0.156 10 false *b 4.208,2.281 4.521,2.438 0.313,0.156 10 false *c 3.875,0.646 4.188,0.802 0.313,0.156 10 false *d 6.448,1.677 6.76,1.833 0.313,0.156 10 false *e 6.771,1.333 7.083,1.49 0.313,0.156 10 false *f 5,2.271 5.208,2.5 0.208,0.229 10 false *g 1.865,1.323 2,1.51 0.135,0.188 10 true A 6.438,0.948 6.75,1.104 0.313,0.156 10 false *d 6.063,0.521 6.375,0.677 0.313,0.156 10 false *c 0.708,0.938 0.917,1.115 0.208,0.177 10 true *1
*1 No. 2 Water By-pass Hose - -
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f RH Side
*g Protrusion of the Radiator Assembly - -



Hide 16515A 21.CONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

a.
A453690

Attach the clamps to connect the intercooler cooling water pipe assembly to the fan shroud.


Hide 88359 22.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 161B0 23.INSTALL ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)

a.
A453736C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Install the electric water pump assembly with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the connector.


Hide 165A0 24.INSTALL NO. 1 INTERCOOLER COOLING WATER HOSE ASSEMBLY (for Water Cooled Type Intercooler)

a.

Attach the clamp.


b.

Install the No. 1 intercooler cooling water hose assembly to the electric water pump assembly and slide the clip to secure the hose.

NOTICE:
·

Make sure the No.1 intercooler cooling water hose assembly is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No.1 intercooler cooling water hose assembly paint mark is aligned with the protrusion of the electric water pump assembly .



A453775C01
4.885,1.813 4.469,1.438 true 5.719,1.708 5.948,1.854 true 6.646,1.177 5.76,1.01 true 5.948,1.844 6.26,2 0.313,0.156 10 false *c 4.854,1.292 5.167,1.448 0.313,0.156 10 false *b 4.188,0.979 4.5,1.135 0.313,0.156 10 false *d 6.375,1.906 6.688,2.063 0.313,0.156 10 false *f 3.813,0.875 4.125,1.031 0.313,0.156 10 false *a 4.885,1.802 5.083,1.969 0.198,0.167 10 false *c 0.885,1.135 1.042,1.292 0.156,0.156 10 true A 6.74,1.479 7.052,1.635 0.313,0.156 10 false *d 6.365,1.75 6.677,1.906 0.313,0.156 10 false *e 5.583,0.906 5.896,1.063 0.313,0.156 10 false *g
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f LH Side
*g Protrusion of the Electric Water Pump Assembly - -



c.

Install the No. 1 intercooler cooling water hose assembly to the intercooler cooling radiator assembly and slide the clip to secure the hose.

NOTICE:
·

Make sure the No.1 intercooler cooling water hose assembly is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No.1 intercooler cooling water hose assembly paint mark is aligned with the protrusion of the intercooler cooling radiator assembly .



A453737C01
5.802,0.875 5.313,0.948 true 4.281,1.333 4.729,1.26 true 6.406,1.198 6.583,0.948 true 4.188,0.833 4.5,0.99 0.313,0.156 10 false *b 4.76,1.177 5.073,1.333 0.313,0.156 10 false *c 6.396,1.729 6.708,1.885 0.313,0.156 10 false *e 6.385,1.885 6.698,2.042 0.313,0.156 10 false *f 5.854,0.781 6.063,1.01 0.208,0.229 10 false *g 4.198,1.073 4.51,1.229 0.313,0.156 10 false *d 0.844,1.333 1.01,1.51 0.167,0.177 10 true A 3.74,0.802 4.052,0.958 0.313,0.156 10 false *a 6.531,0.802 6.844,0.958 0.313,0.156 10 false *c 6.646,1.604 6.958,1.76 0.313,0.156 10 false *d
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f LH Side
*g Protrusion of the Intercooler Coolring Radiator Assembly - -



Hide 16552C 25.INSTALL NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

a.

Attach the clamps.


b.

Install the No. 2 intercooler cooling water hose to the electric water pump assembly and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 intercooler cooling water hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 intercooler cooling water hose paint mark is aligned with the protrusion of the electric water pump assembly .



A453693C03
3.979,2.198 4.177,1.656 false 5.74,0.906 6.302,0.865 false 5.26,2.073 5.635,2.094 false 4.146,0.969 4.458,1.167 0.313,0.198 10 false *d 6.646,1.802 6.958,2 0.313,0.198 10 false *e 6.323,2.302 6.635,2.5 0.313,0.198 10 false *f 5.115,1.969 5.438,2.167 0.323,0.198 10 false *g 6.344,2.083 6.656,2.281 0.313,0.198 10 false *d 3.865,2.24 4.177,2.438 0.313,0.198 10 false *c 6.344,0.792 6.656,0.99 0.313,0.198 10 false *c 2.115,1.646 2.271,1.813 0.156,0.167 10 true A 4.146,2 4.458,2.198 0.313,0.198 10 false *b 3.708,0.583 4.021,0.781 0.313,0.198 10 false *a
*a View A *b 90°
*c Paint Mark *d Front Side
*e Upper Side *f LH Side
*g Protrusion of the Electric Water Pump Assembly - -



Hide 16571C 26.INSTALL NO. 1 RADIATOR HOSE

a.

Install the No. 1 radiator hose to the water outlet sub-assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 1 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 1 radiator hose paint mark is aligned with the protrusion of the water outlet sub-assembly.



A442883C01
5.542,0.427 5.323,0.792 true 6.354,1.281 6.615,0.802 true 3.719,0.542 3.906,1.229 true 3.24,0.448 3.552,0.604 0.313,0.156 10 false *a 3.427,0.792 3.74,0.948 0.313,0.156 10 false *b 4.104,0.719 4.417,0.875 0.313,0.156 10 false *c 3.615,0.365 3.927,0.521 0.313,0.156 10 false *d 6.583,1.729 6.896,1.885 0.313,0.156 10 false *e 6.25,1.99 6.458,2.219 0.208,0.229 10 false *g 0.885,1.104 1.021,1.292 0.135,0.188 10 true A 6.323,2.302 6.51,2.469 0.188,0.167 10 false *f 4.656,1.49 4.969,1.646 0.313,0.156 10 false *f 3.854,0.521 4.167,0.677 0.313,0.156 10 false *e 5.5,0.26 5.813,0.417 0.313,0.156 10 false *d 6.563,0.635 6.792,0.802 0.229,0.167 10 false *h
*a View A *b 45°
*c 30° *d Paint Mark
*e Upper Side *f Front Side
*g RH Side *h Protrusion of the Water Outlet Sub-assembly



b.

Connect the No. 1 radiator hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 1 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 1 radiator hose paint mark is aligned with the protrusion of the radiator assembly.



A442882C01
4.875,1.063 5.219,1.417 true 6.365,0.583 6.104,0.354 true 4.24,0.583 3.927,1.24 true 3.24,0.458 3.552,0.615 0.313,0.156 10 false *a 3.531,0.719 3.844,0.875 0.313,0.156 10 false *b 4.208,0.417 4.521,0.573 0.313,0.156 10 false *c 3.844,0.51 4.156,0.667 0.313,0.156 10 false *d 6.604,1.875 6.917,2.031 0.313,0.156 10 false *e 6.698,2.188 7.01,2.344 0.313,0.156 10 false *f 5.938,0.198 6.146,0.427 0.208,0.229 10 false *g 1.031,1.219 1.167,1.406 0.135,0.188 10 true A 6.323,1.708 6.635,1.865 0.313,0.156 10 false *d 4.74,0.896 5.052,1.052 0.313,0.156 10 false *c
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f RH Side
*g Protrusion of the Radiator Assembly - -



Hide 16470 27.INSTALL RADIATOR RESERVE TANK ASSEMBLY

a.

Install the radiator reserve tank assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the No. 1 water by-pass hose to the radiator assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 1 water by-pass hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 1 water by-pass hose paint mark is aligned with the protrusion of the radiator assembly.



A443704C01
5.021,1.49 5.292,1.771 true 6.615,0.823 6.135,0.823 true 4.396,0.563 4.083,1.219 true 2.49,1.708 2.031,1.823 true 3.271,0.479 3.583,0.635 0.313,0.156 10 false *a 3.635,0.76 3.948,0.917 0.313,0.156 10 false *b 4.354,0.375 4.667,0.531 0.313,0.156 10 false *c 3.99,0.521 4.302,0.677 0.313,0.156 10 false *d 6.531,1.844 6.844,2 0.313,0.156 10 false *e 6.594,2.198 6.906,2.354 0.313,0.156 10 false *f 6.615,0.688 6.823,0.917 0.208,0.229 10 false *g 1.604,2.323 1.74,2.51 0.135,0.188 10 true A 6.208,1.656 6.521,1.813 0.313,0.156 10 false *d 4.875,1.333 5.188,1.49 0.313,0.156 10 false *c 2.5,1.563 2.688,1.74 0.188,0.177 10 true *1
*1 No. 1 Water By-pass Hose - -
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f RH Side
*g Protrusion of the Radiator Assembly - -
V100135

Clip
V100136

Bolt



c.

Connect the No. 2 water by-pass hose to the radiator reserve tank assembly, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 water by-pass hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 water by-pass hose paint mark is aligned with the protrusion of the radiator reserve tank assembly.



A442880C01
5.76,0.625 6.302,0.438 true 5.177,2.073 4.896,1.896 true 4.208,2.281 3.969,1.656 true 1.771,2.01 2.365,1.792 true 3.281,0.5 3.594,0.656 0.313,0.156 10 false *a 3.594,2 3.906,2.156 0.313,0.156 10 false *b 4.198,2.292 4.51,2.448 0.313,0.156 10 false *c 3.875,0.656 4.188,0.813 0.313,0.156 10 false *d 6.406,1.448 6.719,1.604 0.313,0.156 10 false *e 6.729,1.833 7.042,1.99 0.313,0.156 10 false *f 6.323,0.313 6.531,0.542 0.208,0.229 10 false *g 1.729,1.583 1.865,1.771 0.135,0.188 10 true A 6.438,2.177 6.75,2.333 0.313,0.156 10 false *d 4.75,1.76 5.063,1.917 0.313,0.156 10 false *c 2.344,1.667 2.552,1.844 0.208,0.177 10 true *1
*1 No. 2 Water By-pass Hose - -
*a View A *b 90°
*c Paint Mark *d Front Side
*e Upper Side *f RH Side
*g Protrusion of the Radiator Reserve Tank Assembly - -



Hide 16640 28.INSTALL INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)

a.

Install the intercooler reserve tank assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Attach the clamp.


c.

Connect the No. 1 intercooler cooling water hose to the intercooler assembly and slide the clip to secure the hose.

NOTICE:

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.


A453738C01
4.177,1.198 3.875,0.667 false 6.073,0.719 5.521,0.698 false 2.427,0.719 2.635,0.906 0.208,0.188 10 true *A 4.333,0.719 4.646,0.917 0.313,0.198 10 false *b 3.729,0.479 4.042,0.677 0.313,0.198 10 false *c 4.125,0.927 4.438,1.125 0.313,0.198 10 false *d 6.594,2.198 6.906,2.396 0.313,0.198 10 false *e 5.323,0.625 5.635,0.823 0.313,0.198 10 false *c 6.344,2.073 6.656,2.271 0.313,0.198 10 false *d 6.698,2.51 7.01,2.708 0.313,0.198 10 false *f 3.656,0.188 3.969,0.385 0.313,0.198 10 false *a
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f RH Side
V100135

Bolt
V100136

Clip



d.

Connect the No. 2 intercooler cooling water hose to the intercooler reserve tank assembly and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 intercooler cooling water hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 intercooler cooling water hose paint mark is aligned with the protrusion of the intercooler reserve tank assembly.



A453704C02
4.427,1.458 4.906,1.146 false 5.438,1.99 5.646,2.177 false 6.375,1.594 6.302,1.354 false 4.74,1.625 5.052,1.823 0.313,0.198 10 false *b 3.656,0.625 3.969,0.823 0.313,0.198 10 false *a 5.667,2.208 5.979,2.406 0.313,0.198 10 false *c 6.292,2.313 6.604,2.51 0.313,0.198 10 false *f 6.281,2.135 6.594,2.333 0.313,0.198 10 false *e 4.167,0.677 4.479,0.875 0.313,0.198 10 false *d 6.635,1.865 6.948,2.063 0.313,0.198 10 false *d 4.906,1.01 5.219,1.208 0.313,0.198 10 false *c 1.969,1.438 2.177,1.615 0.208,0.177 10 true *A 6.302,1.604 6.615,1.802 0.313,0.198 10 false *g
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f LH Side
*g Protrusion of the Intercooler Reserve Tank Assembly - -



Hide 17030 29.INSTALL AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)

Hide 44360 30.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

a.
A442855

Attach the clamps to connect the vane pump oil reservoir assembly.


b.
A442854

Install the 2 bolts to connect the vane pump oil reservoir assembly.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


Hide 17751 31.INSTALL NO. 1 AIR CLEANER INLET

a.
A442850

Install the No. 1 air cleaner inlet with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12601B 33.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (for Water Cooled Type Intercooler)

Hide 34.ADD ENGINE COOLANT (for Water Cooled Type Intercooler)

Hide 35.ADD ENGINE COOLANT

Hide 51405A 38.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 39.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 40.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)