P0010 Camshaft Position "A" Actuator Circuit (Bank 1)
Diagnostic trouble codes · Vehicles built from Jul 2010
Also covers:
- P0020 Camshaft Position "A" Actuator Circuit (Bank 2)
Versions by build date: May 2007 – Jun 2010 from Jul 2010
DESCRIPTION
The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improves, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0010 |
Open or short in camshaft timing oil control valve assembly for intake camshaft (bank 1) circuit timing (1 trip detection logic) |
|
| P0020 |
Open or short in camshaft timing oil control valve assembly for intake camshaft (bank 2) circuit (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTC P0010 is displayed, check the intake camshaft circuit for the bank 1 VVT system.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- If DTC P0020 is displayed, check the intake camshaft circuit for the bank 2 VVT system.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
- If DTC P0010 is displayed, check the intake camshaft circuit for the bank 1 VVT system.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OIL CONTROL VALVE FOR INTAKE CAMSHAFT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.
- OK:
Tester Operation
Specified Condition
0%
Normal engine speed
100%
Engine idles roughly or stalls
|
|
||||
| OK | ||
| ||
| 2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Remove the camshaft timing oil control valve assembly (for intake camshaft).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω
Text in Illustration *a
Component without harness connected
(Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft))
Connect the positive (+) battery terminal to terminal 1 and connect the negative (-) battery terminal to terminal 2. Check the valve operation.

- OK:
- Valve moves quickly.
Reinstall the camshaft timing oil control valve assembly (for intake camshaft).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Disconnect the intake camshaft timing oil control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- Bank 1:
Tester Connection
Condition
Specified Condition
B49-19 (OC1+) - B24-1
Always
Below 1 Ω
B49-20 (OC1-) - B24-2
Always
Below 1 Ω
- Bank 2:
Tester Connection
Condition
Specified Condition
B50-19 (OC2+) - B25-1
Always
Below 1 Ω
B50-20 (OC2-) - B25-2
Always
Below 1 Ω
- Standard resistance (Check for short):
- Bank 1:
Tester Connection
Condition
Specified Condition
B49-19 (OC1+) or B24-1 - Body ground
Always
10 kΩ or higher
B49-20 (OC1-) or B24-2 - Body ground
Always
10 kΩ or higher
- Bank 2:
Tester Connection
Condition
Specified Condition
B50-19 (OC2+) or B25-1 - Body ground
Always
10 kΩ or higher
B50-20 (OC2-) or B25-2 - Body ground
Always
10 kΩ or higher
Reconnect the camshaft timing oil control valve assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
