2007-2013 Highlander Kluger · Service Manual CRUISE CONTROL SYSTEM

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

E152497E14

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER

  1. E107091E05
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select the following menu items: Powertrain / Cruise Control / Data List.

  1. Check the Data List for proper functioning of the cruise control main switch.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Main switch signal (Main CPU) / ON or OFF
    ON: Main switch on
    OFF: Main switch off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: - / SET switch on
    OFF: - / SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: + / RES (RESUME) switch on
    OFF: + / RES (RESUME) switch off
    -

    OK:
    When the cruise control main switch is operated, the display changes as shown above.
    Result 
    Result
    Proceed to
    OK
    A
    NG (All items are defective)
    B
    NG (1 to 3 items are defective)
    C



B
Go to step 2

C
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT CRUISE CONTROL MAIN SWITCH
  1. Remove the cruise control main switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.E106137E58


Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A-3 (CCS) - A-1 (ECC)
Neutral
10 kΩ or higher
A-3 (CCS) - A-1 (ECC)
+ (ACCEL)/RES (RESUME)
235 to 245 Ω
A-3 (CCS) - A-1 (ECC)
- (COAST)/SET
617 to 643 Ω
A-3 (CCS) - A-1 (ECC)
CANCEL
1509 to 1571 Ω
A-3 (CCS) - A-1 (ECC)
Main switch on
Below 2.5 Ω

  1. Reinstall the cruise control main switch (Click here).



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
E103330E80
  1. Disconnect the spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (CCS) - z1-3 (CCS)
    Always
    Below 1 Ω
    A-1 (ECC) - z1-4 (ECC)
    Always
    Below 1 Ω

  1. Reconnect the spiral cable connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM OR BODY GROUND - ECM)
OK


4. CHECK SPIRAL CABLE
E144333E05

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    z1-3 (CCS) - D53-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z1-4 (ECC) - D53-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.

  1. Install the spiral cable.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D53-1 (CCS) - D55-11 (CCS)
    Always
    Below 1 Ω
    D55-11 (CCS) - Body ground
    Always
    10 kΩ or higher
    D53-2 (ECC) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM OR BODY GROUND - ECM)
OK

REPLACE ECM (Click here)


← Cruise Control Switch Circuit (Aug 2008 – Jun 2010)Cruise Main Indicator Light Circuit (May 2007 – Jul 2008) →