TERMINALS OF ECU
System information · Vehicles built May 2007 – Jun 2010
Versions by build date: May 2007 – Jun 2010 from Jul 2010
| CHECK ENGINE SWITCH |
Disconnect the D22 engine switch connector.


Measure the resistance according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D22-8 (AGND) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the D22 engine switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D22-8 (AGND) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
D22-9 (TXCT) - D22-8 (AGND)
O - V
Key code output signal
Key is not in cabin
Below 1 V
D22-9 (TXCT) - D22-8 (AGND)
O - V
Key code output signal
Press engine switch and hold key close to engine switch*
Pulse generation
(See waveform 1)
D22-10 (CODE) - D22-8 (AGND)
GR - V
Demodulated signal of key code data
Key is not in cabin
Below 1 V
D22-10 (CODE) - D22-8 (AGND)
GR - V
Demodulated signal of key code data
Press engine switch and hold key close to engine switch*
Pulse generation
(see waveform 2)
D22-14 (VC5) - D22-8 (AGND)
G - V
Power supply
Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
Below 1 V
D22-14 (VC5) - D22-8 (AGND)
G - V
Power supply
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
Pulse generation
(See waveform 3)
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the engine switch may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D22-9 (TXCT) - D22-8 (AGND)
Tool Setting
2 V/DIV., 50 ms./DIV.
Condition
Press engine switch and hold key close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 2 (Reference)

Item
Content
Tester Connection
D22-10 (CODE) - D22-8 (AGND)
Tool Setting
2 V/DIV., 50 ms./DIV.
Condition
Press engine switch and hold key close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 3 (Reference)

Item
Content
Tester Connection
D22-14 (VC5) - D22-8 (AGND)
Tool Setting
2 V/DIV., 200 ms./DIV.
Condition
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Disconnect the D36 certification ECU (smart key ECU assembly) connector.


Measure the resistance and voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D36-1 (+B) - D36-17 (E)
B - B
+B power supply
Always
11 to 14 V
D36-17 (E) - Body ground
B - Body ground
Ground
Always
Below 1 Ω
D36-18 (IG) - D36-17 (E)
G - B
Ignition power supply
Engine switch off
Below 1 V
D36-18 (IG) - D36-17 (E)
G - B
Ignition power supply
Engine switch on (IG)
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the D36 certification ECU (smart key ECU assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D36-8 (TXCT) - D36-40 (AGND)
O - V
Engine switch TXCT output
Key is not in cabin
Below 1 V
D36-8 (TXCT) - D36-40 (AGND)
O - V
Engine switch TXCT output
Press engine switch and hold key close to engine switch*
Pulse generation (See waveform 1)
D36-9 (CODE) - D36-40 (AGND)
GR - V
Engine switch CODE input
Key is not in cabin
Below 1 V
D36-9 (CODE) - D36-40 (AGND)
GR - V
Engine switch CODE input
Press engine switch and hold key close to engine switch*
Pulse generation (See waveform 2)
D36-30 (VC5) - D36-40 (AGND)
G - V
Engine switch power supply
Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
Below 1 V
D36-30 (VC5) - D36-40 (AGND)
G - V
Engine switch power supply
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
Pulse generation
(See waveform 3)
D36-40 (AGND) - Body ground
V - Body ground
Engine switch ground
Always
Below 1 Ω
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D36-8 (TXCT) - D36-40 (AGND)
Tool Setting
2 V/DIV., 50 ms./DIV.
Condition
Press engine switch and hold key close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 2 (Reference)

Item
Content
Tester Connection
D36-9 (CODE) - D36-40 (AGND)
Tool Setting
2 V/DIV., 50 ms./DIV.
Condition
Press engine switch and hold key close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Waveform 3 (Reference)

Item
Content
Tester Connection
D36-30 (VC5) - D36-40 (AGND)
Tool Setting
2 V/DIV., 200 ms./DIV.
Condition
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) |
Disconnect the D28 ID code box (immobiliser code ECU) connector.


Measure the resistance and voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D28-1 (+B) - D28-8 (GND)
W - V
+B power supply
Always
11 to 14 V
D28-8 (GND) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the D28 ID code box (immobiliser code ECU) connector.
Measure the voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D28-5 (EFII) - D28-8 (GND)
BR - V
ECM input signal
Engine switch off
11 to 14 V
D28-5 (EFII) - D28-8 (GND)
BR - V
ECM input signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after engine switch first turned on (IG) after battery disconnected and connected.
Pulse generation
(see waveform 1)
D28-6 (EFIO) - D28-8 (GND)
L - V
ECM output signal
Engine switch off
Below 1 V
D28-6 (EFIO) - D28-8 (GND)
L - V
ECM output signal
Engine switch on (IG)
Pulse generation
(see waveform 2)
- If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.
- If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D28-5 (EFII) - D28-8 (GND)
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after engine switch first turned on (IG) after battery disconnected and connected.
Waveform 2 (Reference)

Item
Content
Tester Connection
D28-6 (EFIO) - D28-8 (GND)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Engine switch on (IG)
| CHECK STEERING LOCK ECU |
Disconnect the D10 steering lock ECU connector.


Measure the resistance and voltage according to the value(s) in the table below.
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D10-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
D10-2 (SGND) - Body ground
W - Body ground
Ground
Always
Below 1 Ω
D10-6 (IG2) - Body ground
V - Body ground
Ignition power supply
Engine switch off
Below 1 V
D10-6 (IG2) - Body ground
V - Body ground
Ignition power supply
Engine switch on (IG)
11 to 14 V
D10-7 (B) - Body ground
G - Body ground
+B power supply
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
| CHECK ECM |
Disconnect the B3 ECM connector and measure the resistance according to the value(s) in the table below.


If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
B3-1 (E1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the B3 ECM connector. Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the ECM may have a malfunction.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D32-15 (IMO) - B3-1 (E1)
BR - W-B
Transponder key ECU output signal
Engine switch off
11 to 14 V
D32-15 (IMO) - B3-1 (E1)
BR - W-B
Transponder key ECU output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after engine switch first turned on (IG) after battery disconnected and connected.
Waveform 1
D32-16 (IMI) - B3-1 (E1)
L - W-B
Transponder key ECU input signal
Engine switch off
Below 1 V
D32-16 (IMI) - B3-1 (E1)
L - W-B
Transponder key ECU input signal
Engine switch on (IG)
Waveform 2
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D32-15 (IMO) - B3-1 (E1)
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after engine switch first turned on (IG) after battery disconnected and connected.
Waveform 2 (Reference)

Item
Content
Tester Connection
D32-16 (IMI) - B3-1 (E1)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Engine switch on (IG)
| CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) |
Disconnect the 1M and 1F junction block connectors.
Disconnect the D6, D7 and D8 main body ECU (instrument panel junction block) connectors.


Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D6-1 (AM2) - Body ground
G - Body ground
+B power supply
Always
11 to 14 V
D7-6 (AM1) - Body ground
GR - Body ground
+B power supply
Always
11 to 14 V
D8-1 (GND3) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
1M-9 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
1F-10 (GND1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω