2007-2013 Highlander Kluger · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK ENGINE SWITCH

  1. Disconnect the D22 engine switch connector.
    B146454E05

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D22-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D22 engine switch connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D22-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    D22-9 (TXCT) - D22-8 (AGND)
    BE - V
    Key code output signal
    Key is not in cabin
    Below 1 V
    D22-9 (TXCT) - D22-8 (AGND)
    BE - V
    Key code output signal
    Press engine switch and hold key close to engine switch*
    Pulse generation
    (See waveform 1)
    D22-10 (CODE) - D22-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Key is not in cabin
    Below 1 V
    D22-10 (CODE) - D22-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Press engine switch and hold key close to engine switch*
    Pulse generation
    (see waveform 2)
    D22-14 (VC5) - D22-8 (AGND)
    G - V
    Power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    D22-14 (VC5) - D22-8 (AGND)
    G - V
    Power supply
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the engine switch may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B164407E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D22-9 (TXCT) - D22-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    2. B164408E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D22-10 (CODE) - D22-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    3. B216007E01
      Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      D22-14 (VC5) - D22-8 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  1. Disconnect the D36 certification ECU (smart key ECU assembly) connector.
    B122343E11

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-1 (+B) - D36-17 (E)
    B - W-B
    +B power supply
    Always
    11 to 14 V
    D36-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D36-18 (IG) - D36-17 (E)
    G - W-B
    Ignition power supply
    Engine switch off
    Below 1 V
    D36-18 (IG) - D36-17 (E)
    G - W-B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D36 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-8 (TXCT) - D36-40 (AGND)
    BE - V
    Engine switch TXCT output
    Key is not in cabin
    Below 1 V
    D36-8 (TXCT) - D36-40 (AGND)
    BE - V
    Engine switch TXCT output
    Press engine switch and hold key close to engine switch*
    Pulse generation (See waveform 1)
    D36-9 (CODE) - D36-40 (AGND)
    GR - V
    Engine switch CODE input
    Key is not in cabin
    Below 1 V
    D36-9 (CODE) - D36-40 (AGND)
    GR - V
    Engine switch CODE input
    Press engine switch and hold key close to engine switch*
    Pulse generation (See waveform 2)
    D36-30 (VC5) - D36-40 (AGND)
    G - V
    Engine switch power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    D36-30 (VC5) - D36-40 (AGND)
    G - V
    Engine switch power supply
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)
    D36-40 (AGND) - Body ground
    V - Body ground
    Engine switch ground
    Always
    Below 1 Ω

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B164407E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D36-8 (TXCT) - D36-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    2. B164408E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D36-9 (CODE) - D36-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    3. B216007E01
      Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      D36-30 (VC5) - D36-40 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


CHECK ID CODE BOX (IMMOBILISER CODE ECU)

  1. Disconnect the D28 ID code box (immobiliser code ECU) connector.
    B118534E08

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D28-1 (+B) - D28-8 (GND)
    W - V
    +B power supply
    Always
    11 to 14 V
    D28-8 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D28 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D28-5 (EFII) - D28-8 (GND)
    V - V
    ECM input signal
    Engine switch off
    11 to 14 V
    D28-5 (EFII) - D28-8 (GND)
    V - V
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected.
    Pulse generation
    (see waveform 1)
    D28-6 (EFIO) - D28-8 (GND)
    L - V
    ECM output signal
    Engine switch off
    Below 1 V
    D28-6 (EFIO) - D28-8 (GND)
    L - V
    ECM output signal
    Engine switch on (IG)
    Pulse generation
    (see waveform 2)
    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D28-5 (EFII) - D28-8 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected.

    2. B139210E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D28-6 (EFIO) - D28-8 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK STEERING LOCK ECU

  1. Disconnect the D10 steering lock ECU connector.
    B118684E14

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D10-2 (SGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D10-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    D10-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    D10-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM

  1. Disconnect the B48 ECM connector and measure the resistance according to the value(s) in the table below.
    A206553E13

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B48-12 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the B48 ECM connector. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D55-20 (IMO) - B48-12 (E1)
    V - W-B
    Transponder key ECU output signal
    Engine switch off
    11 to 14 V
    D55-20 (IMO) - B48-12 (E1)
    V - W-B
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected.
    Waveform 1
    D55-14 (IMI) - B48-12 (E1)
    L - W-B
    Transponder key ECU input signal
    Engine switch off
    Below 1 V
    D55-14 (IMI) - B48-12 (E1)
    L - W-B
    Transponder key ECU input signal
    Engine switch on (IG)
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D55-20 (IMO) - B48-12 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected.

    2. B139210E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D55-14 (IMI) - B48-12 (E1)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the 1M and 1F junction block connectors.

  2. Disconnect the D6, D7 and D8 main body ECU (instrument panel junction block) connectors.
    B112605E15

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-1 (AM2) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    D7-6 (AM1) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    D8-1 (GND3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

← TERMINALS OF ECU (May 2007 – Jun 2010)DIAGNOSIS SYSTEM (from May 2007) →