2007-2013 Highlander Kluger · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR DOOR SCUFF PLATE

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


5. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


6. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


8. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


9. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.


10. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


11. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


12. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


13. REMOVE JACK CARRIER SUPPORT

14. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


15. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


16. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


17. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


18. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


19. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


20. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


21. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


22. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


23. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178561
    Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.


24. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


25. REMOVE NO. 1 DECK BOARD (w/o Rear No. 2 Seat)

  1. B178558
    Disengage the 3 clips and remove the rear floor board spacer from No. 1 deck board.


26. REMOVE NO. 1 DECK BOARD (w/ Rear No. 2 Seat)

  1. B178556
    Disengage the 5 clips and remove the rear deck floor box from the No. 1 deck board.


27. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.


28. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Remove the bolt and disconnect the rear seat lap type belt assembly LH.


29. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


30. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Remove the 4 bolts and the rear No. 2 seat assembly.


31. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.


32. REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)

  1. B173614
    Disengage the 8 claws and guide, and remove the rear seat side garnish cap.


33. REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)

  1. B173616
    Remove the screw.

  1. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.


34. REMOVE DECK SIDE TRIM COVER

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


35. REMOVE DECK SIDE TRIM

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.


36. REMOVE SIDE TRIM COVER LH (for LH Side)

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


37. REMOVE SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)

  1. B173610
    Disengage the 4 claws and remove the side trim cover RH.


38. REMOVE REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)

  1. E150364
    Disengage the 4 claws and remove the rear room temperature sensor.

  1. Disconnect the connector.


39. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


40. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)

  1. B173618E01
    Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

    HINT:
    Tape the screwdriver tip before use.


41. REMOVE REAR POWER POINT SOCKET ASSEMBLY (for LH Side)
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


42. REMOVE REAR POWER OUTLET SOCKET COVER (for LH Side)

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


43. REMOVE REAR DECK TRIM COVER (for LH Side without Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


44. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control bezel LH.


45. REMOVE ROPE HOOK ASSEMBLY

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


46. REMOVE NO. 2 DECK SIDE TRIM HOOK (for LH Side)

  1. B173612
    Remove the screw and the No. 2 deck side trim hook.


47. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


48. REMOVE FRONT DECK SIDE TRIM COVER

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


49. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


50. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


51. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Remove the 3 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

    B173622


52. REMOVE REAR AIRBAG SENSOR

  1. C165114
    Disconnect the connector from the rear airbag sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the bolt and disengage the pin, and remove the rear airbag sensor.

    NOTICE:
    Loosen the bolt while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →