2007-2013 Highlander Kluger · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165111E01
    Install the center airbag sensor assembly with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    3. When the ignition switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

  1. Check that there are no loose parts after installing the center airbag sensor assembly.

  1. Connect the holder (with connectors).

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Check that the waterproof sheet is properly set.


2. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)

  1. B168374
    Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.


3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.


4. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.


5. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and clip.


6. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173629
    Engage the 6 claws.

  1. B173628
    Install the console box assembly with the 4 bolts and 2 screws.


7. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B175149
    Engage the 6 claws.

  1. Connect the connector.

  1. B181135
    Install the console box assembly with the 4 bolts and 2 screws.


8. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.


9. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.


10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184679E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


11. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184681E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.

  1. B168370
    Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.


13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B173000
    Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.


14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


16. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


17. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side (Click here).


19. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side (Click here).


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


21. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →