2007-2013 Highlander Kluger · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE COOL AIR INTAKE DUCT SEAL

  1. B172745
    Remove the 11 clips and cool air intake duct seal.


4. REMOVE RADIATOR GRILLE

  1. B172749E01
    Put protective tape around the radiator grille.

  1. B172746
    Remove the 2 bolts and 4 clips.

  1. B172747
    Disengage the 6 claws and 4 guides, and remove the radiator grille.


5. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B172760E01
    Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172761E01
    Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172763
    Remove the 7 screws and clip.

  1. B172764
    Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.


6. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B172760E01
    Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172761E01
    Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172763
    Remove the 7 screws and clip.

  1. B172764
    Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each fog light connector, and then remove the front bumper assembly.


7. REMOVE REAR FENDER SPLASH SHIELD SUB-ASSEMBLY

  1. E150040
    Disengage the 3 clips and 3 guides, and remove the rear fender splash shield sub-assembly.


8. REMOVE HEADLIGHT ASSEMBLY

  1. E150041
    Remove the bolt and 2 screws.

  1. Disengage the claw and disconnect the headlight assembly.

  1. E150042
    Disengage the clamp.

  1. Disconnect the connectors and remove the headlight assembly.


9. REMOVE FRONT AIRBAG SENSOR
  1. Disconnect the connector from the front airbag sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C165112
    Remove the 2 bolts.

    NOTICE:
    Loosen the bolt while holding the front airbag sensor because the front airbag sensor claws and pin (stopper) are easily damaged.

  1. Disengage the 2 claws and pin, and remove the front airbag sensor from the body.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →