2007-2013 Highlander Kluger · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. P input signal is ON.
  2. N input signal is ON.
  3. R input signal is ON.
  4. D input signal is ON.
(B) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. NSW (STAR) input signal is ON.
  2. R input signal is ON.
  3. D input signal is ON.
(C) All switches are OFF simultaneously for NSW (STAR), P, R, N, D, positions (2-trip detection logic).
(D) When any of following conditions for 2 sec. or more in the S position (2-trip detection logic)
  1. NSW (STAR) input signal is ON.
  2. P input signal is ON.
  3. N input signal is ON.
  4. R input signal is ON.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N or D). The ECM determines that there is a problem with the switch or related parts if in receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C171921E01
C171922E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

  1. C117645E72
    Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B5-2 (RB) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

  1. C117645E73
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B5-4 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/o Smart Entry and Start System)
    B
    NG (w/ Smart Entry and Start System)
    C



B
Go to step 8

C
CHECK CRANKING HOLDING FUNCTION CIRCUIT (for 2GR-FE) (Click here)
A


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C110340E93
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    4 - 5
    P and N
    Below 1 Ω
    Except P and N
    10 kΩ or higher
    2 - 6
    P
    Below 1 Ω
    Except P
    10 kΩ or higher
    2 - 1
    R
    Below 1 Ω
    Except R
    10 kΩ or higher
    2 - 9
    N
    Below 1 Ω
    Except N
    10 kΩ or higher
    2 - 7
    D, S, "+" and "-"
    Below 1 Ω
    Except D, S, "+" and "-"
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

  1. C168574E02
    Disconnect the transmission control switch connector of shift lock control unit assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

  1. C168599E02
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    3 - 7
    S, "+" and "-"
    Below 1 Ω
    Except S, "+" and "-"
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (Click here)
A


6. CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

  1. C168527E05
    Connect the transmission control switch connector of shift lock control unit assembly.

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    D32-20 (S) - Body ground
    S, "+" and "-"
    11 to 14 V
    Except S, "+" and "-"
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C168527E06
    Connect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    D32-23 (P) - Body ground
    P
    11 to 14 V
    Except P
    Below 1 V
    D32-22 (N) - Body ground
    N
    11 to 14 V
    Except N
    Below 1 V
    D32-11 (R) - Body ground
    R
    11 to 14 V*
    Except R
    Below 1 V
    D32-21 (D) - Body ground
    D and S
    11 to 14 V
    Except D and S
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)

8. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C169035E02
    Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B5-4 (B) - B2-8 (NSW)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B5-4 (B) or B2-8 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (May 2007 – Jul 2008)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Jul 2010) →