2007-2013 Highlander Kluger · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The system detects the ignition switch's starting signal (STSW) and then supplies current to the starter until the ECM judges that the engine has started successfully. The purpose is to reduce the holding time of the ignition key.
A166695E02

WIRING DIAGRAM

A172774E02

INSPECTION PROCEDURE


1. CHECK CRANKING
  1. When starting the engine, check whether the starter motor starts.

OK:
Engine is cranking.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. READ VALUE USING INTELLIGENT TESTER (STA SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG) and when the engine is started.

    OK:
    Display (Starter Signal)
    Condition
    OFF
    Ignition switch on (IG)
    ON
    Engine start



NG
Go to step 10
OK


3. INSPECT ST RELAY

  1. B016200
    Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied terminals 1 and 2
    Below 1 Ω

  1. Reinstall the ST relay.



NG
REPLACE ST RELAY
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

  1. A172726E01
    Disconnect the park/neutral position switch connector.

  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    B5-5 - ST relay terminal (2)
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    B5-5 or ST relay terminal (2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reinstall the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
OK


5. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

  1. A172711E01
    Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal (2) - Body ground
    Always
    Below 1 Ω

  1. Reinstall the ST relay to the engine room relay block.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)
OK


6. INSPECT TERMINAL VOLTAGE (ST RELAY TERMINAL)

  1. A172711E01
    Remove the ST relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal (5) - Body ground
    Always
    9 to 14 V

  1. Reinstall the ST relay to the engine room relay block.



NG
Go to step 9
OK


7. INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here).



NG
REPLACE STARTER ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

  1. A172722E01
    Remove the ST relay from the engine room relay block.

  1. Disconnect the starter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal (3) - B12-1
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal (3) or B12-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the starter connector.

  1. Reinstall the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - STARTER ASSEMBLY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

9. INSPECT FUSIBLE LINK (ST FUSE)

  1. A168235E09
    Remove the fusible link from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Fusible link
    Always
    Below 1 Ω

  1. Reinstall the fusible link.



NG
REPLACE FUSIBLE LINK
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER RELAY)

10. CHECK ECM (STAR AND STSW VOLTAGE)

  1. A168199E23
    Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B3-12 (STSW) - Body ground
    Cranking
    9 to 14 V


    Result:
    Terminal STAR
    Terminal STSW
    Proceed to
    9 to 14 V
    9 to 14 V
    A
    0 V
    9 to 14 V
    B
    0 V
    0 V
    C



B
REPLACE ECM (Click here)

C
Go to step 15
A


11. INSPECT PARK/NEUTRAL POSITION SWITCH

  1. A172729E01
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    Below 1 Ω
    N
    2 - 9, 4 - 5
    Below 1 Ω
    D
    2 - 7
    Below 1 Ω
    2
    2 - 3
    Below 1 Ω
    L
    2 - 8
    Below 1 Ω

    Result: 
    Result
    Proceed To
    OK
    A
    NG (with U151E))
    B
    NG (with U151F)
    C

  1. Reconnect the park/neutral position switch connector.



B
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
A


12. CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

  1. A172725E01
    Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    B3-11 (STA) - B5-5
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    B3-11 (STA) or B5-5 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)
OK


13. INSPECT RELAY (ST CUT RELAY)

  1. B016200
    Remove the ST CUT relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage applied terminals 1 and 2
    Below 1 Ω

  1. Reinstall the ST CUT relay.



NG
REPLACE RELAY
OK


14. INSPECT TERMINAL VOLTAGE (ST CUT RELAY TERMINAL)

  1. A172710E01
    Remove the ST CUT relay from the engine room relay block.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 - Body ground
    Ignition switch on (IG)
    9 to 14 V

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST CUT RELAY - IG2 RELAY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST CUT RELAY - BODY GROUND)

15. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)

  1. A172727E01
    Disconnect the ECM connector.

  1. Disconnect the main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (check for open):
    Tester Connection
    Condition
    Specified Condition
    B3-12 (STSW) - D9-4 (STSW)
    Always
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Condition
    Specified Condition
    B3-12 (STSW) or D9-4 (STSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH ASSEMBLY)
OK

CHECK SMART ENTRY AND START SYSTEM (Click here)


← Cranking Holding Function Circuit (May 2007 – Jul 2008)Cranking Holding Function Circuit (from Jul 2010) →